Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
Hello,I have attached a diagram for the design that we're in the process of migrating to. My Security Admin wants to add a pair of ASAs running in HA to filter traffic between the campus and data center. He's looking at the 5585 which will require t...
Hi, guys, I ran into a weird situation here: From the gateway switch with interface vlan 500 and 501, I pinged one destination in vlan501 and vlan500 respectively. The results are as follows:====================switch#ping 3.27.113.230 repeat 5...
I am trying to figure out some information for the Cisco Series 800 Router. I went through the manual but could not find any specfic information that i require. I am in search of password capabilities and levels of access for the router. Further, I...
Hi team.I've checked the feature navigator and it says that this code supports both SSH v1 and v2 but it seems that it doesn't.SW11(config)#do sh ver | i IOSCisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(50)SE5, RELEASE SOFTWARE (f...
Currently we are building our new network and after a successful test off site we are now experiencing the following behavior we are not able to explain.Situation :We have 2 Cisco Nexus 56128P (running 7.1(1)N1(1) ) switches as our core layer, via t...
We have "WS-SUP720-BASE 2 ports Supervisor Engine 720 Rev. 2.3" Can I configure VSS on SUP720 base supervisor. NAME: "5", DESCR: "WS-SUP720-BASE 2 ports Supervisor Engine 720 Rev. 2.3"PID: WS-SUP720-BASE , VID: , SN: SAD0742...
Hey -we are doing a rip and replace at a site and one of the things we would like to get rid of is an old content switch. Haven't configured any SLB before and was looking for any info on configuring SLB on 3850, but haven't found any. Is it supporte...
Hello,This is not a Routing/Switching query but thought you would help me.I need to find out which DNS server is authenticating TACACS users when they try to logon to switches .. I can't find any attribute that tells about passed authentication users...
I want to change my ip domain name in my switch from angle.com to angel.com, currently my show cdp neighbours shows all connected devices as xxxxxxx.angle.com.what needs to be considered before changing the domain.
I need to add interfaces to a production port-channel. The problem is that I am at the 8 interface limit for the port-channel, and I have 6 interfaces assigned to the port-channel that were interfaces on blades that are no longer in the chassis. I ...
Hi,Is it possible to set a schedule on policy-map? although there;s scheduler using ratio in bandwidth.Also when using access list is there any chance that we can add schedule?thanks Regards,A.
Is it possible to run STP over VPC? I think it is not possible. This was an interview question asked to me. Could someone confirm please?
Hi Community, I am trying to restrict internet only access for a specific vlan e.g ( 620 Vlan - 172.16.62.0/24 ) but when l apply the following access lists to the 620 Interface response time seems to be very slow ? If l remove the specific access-l...
Hello, We are trying to implement WCCP in our network for LAN and VPN users. Here's a little info about our network: - WCCP redirection is configured our cisco 4500, connected directly to the proxy server - We have 2 VPN appliances for remote access,...
Hi There,I am confused regarding VRF communication between two devices to maintain multi tenant environment, for example we have edge router which is making VPN's with different customers and further it used VRF to isolate customers traffic from each...
