Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
How do I set my cisco catalyst 3560 to use a static ip instead of an ip from our DHCP server? I want to monitor it with nagios and would like it to use an ip from our static range.
Hello, if you run a continuous ping from a computer, and then repeatedly re-plug that computer in to different switch ports (for instance re-plug every 10 seconds), will this cause problems ?From what I understand, the ping running from the computer ...
Hello,We are looking at putting together a solution using dual stacked 2960XR switches, which are linked to the core. The 2960XR will be running OSPF for routed access and we have been asked to provide some figures for the performance of the switch w...
I'm an IT tech for a non profit organization in NYC with around 250 employees. We are moving to a new location next week, so our IT room has to be moved and re assembled at the new location. We have 15 switches, 2 routers and a ASA 5510 firewall. Is ...
There are 2 3760g catalyst stacked using 2 StackWise cables.Then the 2960s are stacked using 4 ports as etherchannels.The switches work fine. Now where I’m having a problem is I want to set up a second etherchannel between the 3760s and the 2960s. I ...
I am trying to update our Banners and MOTD on our routers/switches (various models 2900s/2800s/2960s/3750s/4500s/6500s). As I am in Canada I need to create them in both French and English, the French has special characters such as è or à and many ot...
Hi everyone:I have an issue regarding route injection between a vrf interface and a global interface.The configuration is something like this:I need vrf V1 network and 192.168.2.0 network reach each other.I tried straight routes at first but it didn'...
This is to support a user who has the requirement of simulating specific speeds for download/upload. We have configured a limit using service-policy that as successfully limiting upload speed (ingress on the interface) but we (more importantly) need...
I would like to copy the config from an existing ESW540 switch to a replacement of the same model. How would I do this? There is no CLI in the ESW540's.
Hi, is there any requirement of setting bandwidth of vlan equal to interfaces(fa or gi? another question) of switch?what will happen if we set vlan bandwidth lower than the interface? Thanks,Visha
Hi, What are mac address cpu entries? Vlan Mac Address Type Ports—- ———– ——– —–All 0100.0ccc.cccc STATIC CPUAll 0100.0ccc.cccd STATIC CPUAll 0180.c200.0000 STATIC CPUAll 0180.c200.0001 ...
Hello guys, I have an issue here with my 2960SI switch..I decided to upgrade it with a newer IOS (previosuly it had some version of lanlite and worked fine)I have tried the common 2960S IOS versions, but all of them were hanging after saying "image u...
I have a standard acl configured on a vlan interface. logs show that ntp packets are being blocked even though the acl permits it.acl:190 permit udp host 10.0.0.1 10.5.51.0 0.0.0.255 eq ntp log%SEC-6-IPACCESSLOGP: list VLAN551-OUT denied udp 10.0.0.1...
HiI am currently installing a new 3650 stack which will service user mitel phones and pcs. In the past, I have used 3560s and 3750s where you need to enable qos globally and on the interface level.My question - is this - it seems that the new 3650 XE...
Hi All,Our office network setup is ISP-------ASA---------3750---------2960X (stack by 4)-----------wired usersRecently, I use command "show arp" in 2960X, the output as below,In arp table, I can't see wired PC mac address, and also I do a test at las...
