Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Hi,If am configuring COS based ingress/egress queuing on mpls interface, whether the line card/switch is able to see the COS marking on mpls packets or not. Line card is - WS-X6724-SFP.Below are the configuration done under interface..  wrr-queue ban...

jofin Yoj by Level 1
  • 543 Views
  • 1 replies
  • 0 Helpful votes

I have to delete all the VLANs and other saved configurations on this Switch and reset it to factory(default) settings. Please help me!! What commands I have performed so far : 1) Write Erase 2) VTP mode transparent 3) No VTP Password 4) Delete flash...

I am working on a network that is majority HP Comware switches running MST instance 0 for all VLANs. I have approx 12 Cisco switches also running in MST spanning-tree instance 0 configuration for all VLANs. The Root bridge on the Cisco switches are t...

HelloIm trying to configure DSCP taggning on a C2950 switch. I have tried different approaches with no success.1) Use of access-list, class-maps and policy-maps applied to both phone interface and uplink interface in a configuration such as;mac acces...

Hi All, Must be missing something here.  I have a need to turn up VPN services on a 867vae router but it has ipbase and I need Security.  I'm trying to find out UDI etc.. but I don't have the "sh license" command available so I'm a bit stumped.  Curr...

Hi everyone, im about to start a diploma in computing and IT, one of the modules is around networking, I have no experience in this field and was wondering if I will be able to grasp it? I have a decent understanding of working Pc's doubt this will h...

bri_99001 by Level 1
  • 749 Views
  • 4 replies
  • 0 Helpful votes

How can I force EIGRP to prefer external vs internal route? I have used delay in the past to influence route selection but here you can see everything but internal vs external is better via 10.100.25.1. The config below is from a core router with 1 g...

Dear all,I am getting the following message in our VSS.Sep  2 05:56:18.501: %CDP-SW1-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on GigabitEthernet1/2/29 (304), with HQ-DC-CSW-VSS.abc.comGigabitEthernet2/2/28 (300). interface GigabitEther...

Hello,I just configured our first cluster of Microsoft servers using Multicast NLB.The gateway of the VLAN is a Cisco 5540 and the servers are connected on a Cisco 3750 stack.In order to let the ASA forward the frames for this multicast group I had t...

p.caforio by Level 1
  • 14869 Views
  • 12 replies
  • 0 Helpful votes

Hello, I am confused as to connecting 3 3750X switches for stackpower. I have seen 3 different ways of connecting the stackpower cables and am confused as to which way I should connect them. any and all help is appreciated.

 Hi, I want to connect a c7000, B22HP card to our 5548s. Can I use FET SFPs on the c7000 side and the 5548 side? Thank you I found this document a little unclear - this is what I referenced. http://www.cisco.com/c/en/us/products/collateral/switches/n...

Hi, We got an issue with N7K. At lot of user around 10,000. The WLAN VDC connecting 4 of WLC5508 goes out of service. We'are holding a couple of N7K peering each other. We allocated a few port for this WLAN VDC. We can not even figure out what the r...

I saw some previous topics  regarding MSTP and  PVSTP interaction but I still have some uncertainties. Also I've read the "understanding MSTP article" from cisco's website. my setup i:c1 -----c2c1 needs to be root for vlan 1-20c2 root for rest of the...

Review Cisco Networking for a $25 gift card