Resolved! Help with routing issue, thanks!
.
.
Dear all,I have 2 Cisco Nexus 5000 with each 2 Nexus 2000 in FEX Mode. My Vlan are all in fabric mode.I would tried to connect a catalyst 3750-X and a nexus 2K together in trunk with filter vlan.NEXUS 2000 <== Port-Channel ===> Cisco 3750XN2K :Po: sw...
Help Please..Error loading "flash:c2960s-universalk9-mz.152-1.E1/c2960s-universalk9-mz.152-1.E1.bin"Interrupt within 5 seconds to abort boot process.Loading "flash:/update/c2960s-universalk9-mz.150-2.SE5/c2960s-universalk9-mz.150-2.SE5.bin"...Error l...
I am configuring the eigrp under the 3750X with IOS c3750e-universalk9-mz.150-2.SE4.bin, the 'eigrp stub connected summary' is there by default, I tried to NO it, but I could not, what is the purpose of this command by default out thereThanks
Hello,If I have the access lists configuration mention below. As far the order of operation the router will start top to down until it finds a match. However, let say it permits 10.87.21.155 will it stop there if it finds matches that IP address or...
Hi all, Please educate me the following scenario : I have Nexus 7010 with 2 L3 modules, N7K-M132XP-12L and N7K-M148GT-11L. Now to increase more ports for end devices, I add in the module N7K-F248XP-25E and believe it's for Laye...
Hello, we have a very old WS-C2980G-A that I'm trying to configure.It says on the front it is Ethernet 10/100/1000, but when I see port speeds it only goes to 10/100 and 1000 is not an option in the IOS.I've looked at the manual and its going over gi...
HiWe just purchased new 3750X and got the Cisco license key from the vendor, is there anything I need to do with this Cisco license key? Like software activation?Thanks
hi expert,we have Cisco VPN conecntrator 3000 series as this is EOS/EOL i want to move all the configuration to existing asa 5520 VPN box. Current Existing configuration on these boxes are below. I just want to know what is the capability of ASA 5520...
Hello,I'm looking at a pair of old 6509 switches. On one switch port 15/1 (the MSFC) is configured with an ISL trunk. On the other switch there's no port config showing for 15/1.I understand there's an implicit internal trunk created between the PFC ...
I have 1 stack of 3 3750X switches.BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE1, RELEASE SOFTWARE (fc1)I have a pc attached to switch 3 port 29 (g3/0/29)interface GigabitEthernet3/0/29 switchport access vlan 900 switchport mode a...
Hi,I've have a case where the Sup card does not see the USB or the SD card. I have a pair of switches exactly the same running the same code. When I try on the other switch it works fine for both.Image: cat4500e-universalk9.SPA.03.04.00.SG.151-2.SG...
Hi, Here is a really basic question: i'm trying to connect to the console of a catalyst 2960-s, using a regular micro-usb cable, AND/OR a regular rj-45 with a db rs-232 converter. With the usb cable: one end in the usb port on the switch, the other e...
Hi All,I know that these two are the wiring shemes for the utp cables for connecting to rj45 connector.Actually if we connect both the ends in either T568A OR T568B, then it is called as a straight through cable.And if we connect one end as T568A an...
Dear All,What is the command to reduce the Multicast Group managed by the Randevouz Point?ON regular IOS is ip pim rp-address CORE1IP access-list MULTICASTACLbut on the NX-OS we were unable to find a similar command:Any ideas?Many thanks,Francesco
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-08-2024 01:20 PM | ||
10-08-2024 12:54 PM | ||
10-01-2024 04:28 AM | ||
09-27-2024 06:10 AM | ||
09-25-2024 01:15 PM |
User | Count |
---|---|
8 | |
8 | |
6 | |
6 | |
5 |