Hi,How to enable UPNP on CISCO routers - 36XX , How can I simualte UPNP connections.Thanks
Hi,How to enable UPNP on CISCO routers - 36XX , How can I simualte UPNP connections.Thanks
Hello folks, Imagine I am designing a small network with a C2900 router running OSPF and in the future BGP with service provider. Please see attached diagram.The router is connected to (2) C3750 Layer 3 distribution switches. Then one C3560 layer 2 ...
Hi everybodyI am reading about different ip sla operations . For example, icmp operation will give us information about jitter, round trip delay, or whether the remote node is reachable or not. But there are other operations such as RTP, TCP connecti...
hi all, i have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I dont know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the...
Hello all,I have a small lab setup and I am trying to implement an IDS/IPS on the network. I have 3 VLANs setup (10, 20, and 30) with the switch and a router allowing for inter-vlan communication. Port FA 0/1 on the switch is setup as a trunk using 8...
Hello,Is there a script to create 10000 static nat statements with port forwarding? 10000 to 10000, 10001-10001, etc..Thanks.evanibev@cox.net
Hi all,Trying to configure 1811w for wi fi .Need to use authentication shared keys but current IOS seems does not support irRouter(config)#int dot11Radio 0Router(config-if)#ssid manvee1Router(config-if-ssid)#a?% Unrecognized commandRouter(config-if-s...
Hi Everyone,Need to confirm belowwhen we do sh spanning tree vlan on switch Port 12 (FastEthernet0/12) of VLAN0020 is root forwarding Port path cost 19, Port priority 128, Port Identifier 128.12. Designated root has priority 24596, address 000d.2...
I am still struggling wit telnet options.I have this scenario:3 x 2801 routers1 x 2811 router.1 X 3550 poe switchAll of the routers have ip adresses starting with ranges 10.10.X.XBut they all have different subnets.i have statically gave my laptop 'n...
Does anyone know if you have redundant sup VS-S2T-10G-XL if the 10G interfaces on both supervisors are active?Sent from Cisco Technical Support iPhone App
Hello, imagine I want to make VLAN200 workstations communicate like the show in the attachment. What would be the default gateway to be configured in the workstation? If I configure 192.168.1.1 as the default gateway (R1 interface ...
hi , im trying to assign ipv6 pool in a router and want the interface loopback2 to be the default gateway of the poolassume i have the prefix 2aaa:aaa::/64 what i want is :i just want to put an ipv6 addrresst to interface on my router , and use w...
my LAN setup is running on VLAN1, now I have added layer 3 switch to run intervlan routing. On access layer I have some switches which are connected on access port not trunk port, do I need to configure Trunk Port on all switches as I...
We have 2 3750 24 port fiber switches in a stack and we would like to change the member to become the master. Both are running the same IOS and they are alive on the network. I read that you can change the who becomes the master by setting the priori...
I am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-23-2025 01:45 PM | ||
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM |
User | Count |
---|---|
13 | |
11 | |
9 | |
5 | |
4 |