Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

Been trying to config a 2924XL switch via telnet. Always within Two(2) minutes. the switch reboots and knocks the telnet session down.When I unplug the switch it will once again hookup but only for a couple of minutes.Any suggestions ?Thanks;

I have 6509 with dual sups, the secondary sup has failed and I am not able to bring it up even after reboot. the state says unknown/other. Does anyone know what that state" unknown" means?. I could not find any documentation about this state.Actions ...

blach1980 by Level 1
  • 4041 Views
  • 5 replies
  • 0 Helpful votes

Guys, Can you please confirm the commands in order to add any access list in the existing existing standard access list. For an example, there are two actions happening (10, 20) in the standard access list and I need to add a new (permit/deny) action...

ray_stone by Level 1
  • 1267 Views
  • 5 replies
  • 0 Helpful votes

Hi all, i'm trying to find information about the licesing of ios package. I need to upgrade a C2911 from 15.1 to 15.2, the router have a permanent uc license, will be that license permanent also after the upgrade?I'm not able to find documentation ab...

cbrasolin by Level 4
  • 2748 Views
  • 6 replies
  • 0 Helpful votes

I'm looking for a 24-port SFP switch. Each of the two switches in the subject meets that requirement.  If I went with the ME switch over the 3750 (at about half the cost), what features/functionality if any, would I be giving up?  (I'm not concerned ...

stefross by Level 1
  • 1823 Views
  • 5 replies
  • 0 Helpful votes

Our organisation is looking at migrating a switch block of approximately 16 switches (distribution and access), 350 defined vlans and 7 MST regions, to Rapid-PVST.Just wondering if anyone has done this (or hasn't) and has some tips, pointers, informa...

le_ by Level 1
  • 3912 Views
  • 5 replies
  • 0 Helpful votes

Good morning,I'm trying to access the swith to erase all users IP information for each line etc,I've run the following commandsflash_initload_helperbootThe switch reboted ok but i cannot access the switch as it has a motd banner and login, how do i g...

I am trying to setup VLAN's in the company I work for and I am almost there but missing the part when the internet works.I have an SG300 as a L3 Router IP 192.168.0.93I have created VLAN20 and VLAN40Assigned VLAN20 192.168.2.1 and VLAN40 192.168.4.1T...

Hi there,I've been asked for recommendations on upgrading the switching infrstruature for a smallish company.The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have...

Hello,     I've been  working on breaking down and understanding the default auto qos  configuration on a Cisco 3750 in the hopes of putting together a QoS  strategy that will fit our environment.  I'm having some difficulty  understanding how the "m...

Hi, can anyone help?I have a WS- C2924C-XL switch that I would like to upgrade the IOS version on. The IOS version in question can only be installled on an 8MB version of this switch, I have tried to confirm the amount of memory present in the device...

Ellerby01 by Level 1
  • 1085 Views
  • 5 replies
  • 0 Helpful votes

Could you please give me some advice on ways to improve the layout of my network? I currently have the following equipmentRouterCisco 2821Switches29502950Switches in Stack3750G37503750I've purchased two 2960 gigabit switches to replace the two 10/100...