Just a simple question here, (yes I'm still a beginner):I have a router which the inside interface is hooked to a PC with the IP address 10.1.0.1.I want to access that PC with ssh; (from the outside) I did the command on the router:Router(config)# ip...
Hi,Please help in finding the Heat dissipation or Heat generated by the cisco devices in the attachment.Any Quick Reply will be appreciated.Regards,M AWAIZ ALI
hello,i am experiencing intermittent CPU high situation at a client site. I have 2 6509-E chassis with SUP-720-VSS and classic line cards :-(. on October 2011 the switch reached 100% CPU on both devices and the entire network went down. Customer rest...
Hi everybodyI passed ccnp route exam a week ago and I would like to thank all of you for your great help ; Now i am starting my study for switch after one-week of much needed break.My book says one can design campus network using hierarchical net...
Good afternoon,We are using Cisco 3750 switches in our environment as distribution switches.We currently use to police inbound traffic, but we need to find a solution to limit inbound traffic per IP.Something like this “Inbound traffic for each IP ca...
ip nat pool tester1 10.0.0.1 10.0.0.2 netmask 255.255.255.0The pool will contain two ip address for NAT 10.0.0.110.0.0.2How do you set it up so the pool only contains one ip address and works as ip nat pool tester1 10.0.0.1 10.0.0.1 netmask 255.255.2...
hello guys,I have been facing this issue since couple of days with 2 of my switches. trunk port, access ports changing status to down/up every 5 seconds. not stable.please can someone point me in right direction.see the attached log & configurationth...
Hi,I am using 3560.IP rouitng is being turned off on this.Curious to know if I will create etherchannel or port channel.I think etherchannel.Correct me if I am wrong.On connecting switches I have vlan10,20,30 to be allowed.I am sure I need to allow t...
Hi,All the other switches / routers on quering for SNMP sysName.0 returns their FQDN in our network. The Nexus 7010 and 5020 switches in the network return only their name. "hostname xx" and "ip domain-name xx" defined on all the devices. The SNMP MI...
We have seen high CPU utilization on some Cisco switches of type 2960S. Also we got info, that applications are running with poor performance or with interuption. Is this a know problem?Following IOS is loaded: C2960s-universalk9-mz.122.55.SE
Hello,I'm trying to create a subinterface on the WS-C4507R+E (IOS 15.0(2)SG2, Sup 6L-E 10GE) but keep getting invalid input. switch(config)#int g5/11switch(config-if)#no switchportswitch(config-if)#int g5/11.20 ^% I...
Hi GuysI am replacing, Cisco 3845 (ISR) by Cisco 3945 (ISR2), and have some question.NM-4T work with CAB-V35MT is replaced by HWIC-4T with CAB-SS-V35MT?NME-AIR-WLC8-K9 is replaced by SM-SRE-700-K9?Which is the replacement of EC-MFT-64 ?Thanks for yo...
Hi All,Let say I have two 48 ports switches, one vtp domain set as "site1.example.com", another vtp domain set as "site2.example.com". Both switches has VLAN 201 to 248, assigned to port 1 to port 48. VLAN 201 to VLAN 245 in switch 1 are assigned to ...
Hi AllIf I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960thanksSaquib
On a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.After it came back up again, the redundancy status sti...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 04-23-2025 06:26 AM | ||
| 04-23-2025 06:18 AM | ||
| 04-19-2025 09:40 AM | ||
| 04-15-2025 04:52 AM | ||
| 04-11-2025 03:44 AM |
| User | Count |
|---|---|
| 9 | |
| 6 | |
| 5 | |
| 3 | |
| 3 |
