FolksWhat is a good way to find a post that I posted in this community? I typed my user-id and keyword to search, but this is not good way. Anyone can share experience? Thanks
Forum Posts
Dear Sir or Madam, I have registered in Netacad, after I installed Packet tracer the software shows to me a black screen. recently I know this black screen contains the user name and password for Netacad.the issue I can not log in and I used the PT ...
I need to know the total power consumption of an Aruba 48 port POE 740 wall switch
Resolved! C9300L-24P-4X - POE Issue
Hello Everyone, Could you please help me with the below issue? After the switch restart PoE is not working, is this a bug or hardware failure? *Nov 2 11:21:42.073: ILP:: PoE POST failed on slot 1 , skip PoE event to state machine.*Nov 2 11:21:42.073:...
Hello,I would like some help because I have a problem.I have a remote site, where I replaced the switches with 9200s.This site is linked to the central site by an operator VPN link. I don't have control over the operator routers.On this remote site, ...
Hello Everyone,The Cataly60 Plus Series PoEnda is constantly repriced 29 comments on the st.Thank you for your support."flash:/c2960-lanbasek9-mz.152-2.E7/c2960-lanbasek9-mz.152-2.E7.bin" yükleniyor...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ...
Getting the following error on a C9500, one port only.10:10:53.130: %SFF8472-3-THRESHOLD_VIOLATION: Twe1/1/0/19: Rx power low warning; Operating value: -9.2 dBm, Threshold value: -8.0 dBm.The error registers in the log, every 10 minutes. Steps I hav...
Hello everyone!!! I can't understand what is chassis in cisco devices. All I know chassis is a hardware part of the network device. But what does it contain? Are network interface, fan, power supply part of chassis? All cisco dievices have chassis? C...
I Have intrenet connection through ISP connected to CE router Cisco 888 k9 deviceMy Lan Subnet configured on int vlan 1i can reach any site with source int vlan 1 with size 1500 nourmaly and with don't fragment also.The problem that when i connect la...
I am looking for a way to use the Cisco Business Dashboard API to fetch the devices currently connected to each port of a switch (Mac Address Table). This would then be used to map devices by mac address to specific configurations. It looks like by f...
Resolved! BPDU filter
After some study, I understand that BPDU filter global command will enable BPDU filter on PortFast enabled ports and stop those ports from send/receive BPDUs. According to Cisco article, if those ports received BPDUs, PortFast will lose it state and ...
Hi,our WS-C3850-12XS Stack is running on SW Version 16.6.4a.Can we go direct from 16.6.4.a to Version 16.12.07 or to any 3.6/3.7 Version, or are there versionswe need to install between.Regards
Hi all,I need some help to understand the stepwise approach to split my existing core switch stack of 2 x c9500 into separate core switches(like Core1 & Core 2). Will appreciate your help.Switch Model : c9500-12QSW : CAT9K_IOSXE Regards,Shehri
So a Im trying to get a list of MAC addresses using the command sh mac address-table | e Gi1/0/25 | Gi1/0/13 | Gi1/0/4 But i dont want to see these 3 ports in specific, the way this command is entered right now it only excludes Gi1/0/4 and i still se...
