Switching

Dear friends,I need to modify an access-list bound to a route-map for PBR.Is it ok if i modify the access-list directly or should i disasociate the route-map from the interface before i make the access-list changes?Thanks a lotGautam

I have two 6509 switches running HSRP between them for all vlans.  I have a 7204 with a DS3 pipe connected to only one of the two switches and I would like to connect the router so that it is connected to both switches.  I tried using bridging, but H...

Hi Experts,I have Cisco 1841, Internet link terminated on Fa0/1 and MPLS routing done on this router.Recently we are getting alerts like below High input packet queue drop.....EVENT ID                = 00064KQALERT ID                = 000018ITIME    ...

Hi All,I have a design as attached, the corcern is budget. My question:=Option 1=-If I use 2 access swith 2960G-24TC-L, can I use copper cable to have trunk link?Since this series is equipped either to use copper or fiber for last 4 ports.(No need to...

In Cisco 7600, I created a named aggregate policer: AGGRE. Then I call the same aggregate policer from 2 different policy-map (POLICE-2 and POLICE-3) using the police aggregate command. Note that in each policy-map, the aggregte policer is called und...

I want to monitor fa1/0/19's traffic to fa1/0/13 by RSPAN.My configuration is as follow, but I can't capture packets on interface fa1/0/13, please give me some help, thanks.========interface FastEthernet1/0/13 switchport trunk encapsulation dot1q swi...

Hi all,CORE1#sh bootflash:-#- ED ----type---- --crc--- -seek-- nlen -length- ---------date/time--------- name1   .D image        5FE60C1E  C63FF8   30 12468088 Jan 12 2006 15:36:24 -05:00 cat4000-i5s-mz.122-20.EWA3.bin2   .. image        93B32579 184...

Hi,Using the "transform set" commands and the "crypto isakmp" commands which vpn does that make it is it ipsec, ssl vpn or gre?If the above quewstion doesn't make sense can someone please point me toa basic explanantion of the differences?ThanksDan

Network:     TMG 192.168.1.1/24 This is the route outThen have the L3 switch hereThen the layer 2 switch here     With vlan's 10 - 20 - 100 on it.I only want to route the 10 - 20 vlans, the 100 vlan is a dmz that will go all the way back to TMG.I wan...

I have a 3750 stack as my aggregation point (10.10.10.3).  Outbound traffic goes to ASA5510 (10.10.10.1) as do all my client gateways.  I recently received a 1910 (10.10.10.10) to use as VPN router from an ISP vendor.  I simply want to route traffic ...

Dear All,   Let me explain the scenario which i have in my network.  There is firewall outside interface and two routers LAN are connected to unmanagable Switch and there is a network X.X.X.X configure between these three devices.I have configured HS...

Hi all,My 6509E Chasis cannot detect the all the line card except the ws-x6k-sup2-2ge. It is running hybrid which Cat0S on layer 2 and IOS at Layer 3.The more detail log is in the attachment.is it this problem is because the CATOS version cannot supp...

I understand that redundant supervisor is not required in running VSS in the C6500 series chassis. (i.e. 1 sup engine per chassis, for the two chassis interlinking with 10GE).What would happen if the sup engine in one of the chassis fails? If there a...