Switching

WHat is the maximum amount of flash memory that I can install in a 2691? Also, can I use any standard flash card for the 2691?

Hello,I have a L2 port-channel between 6509 to 3750 stack switches. There are couple of VLAN's sent between these swiches. I need to prioritize traffice following through a particlar VLAN say VLAN250. How do I configure the QoS for these switches to ...

Hi allcan anyone tell me when my switch trusts the frames from the phone, what do I need to do on the uplink port to my router, do I need to just enable diff serv on it and get it to trust the frames on both ends of the uplink, the switches are layer...

It redistributes static routes without a default-metric command! Found on Catalyst 4500 with 122-37.SG1.Former IOS version stop redistribution of static routes without a command like “default-metric 10000 1 255 1 1500”Now is “router eigrp 123â€...

Dears,I have two cisco routers connected to a firewall through a multi-layer switch ,I tried to configure glbp on the two routers on fastethernet interface but the problem is when I shutdown fa interface to test glbp the router remain in the "Init st...

Hi guysPlease can you assist i am presently trying to recover an 1841 from rommon mode by using xmodem but it keeps giving the following, Will paste in actual text from router"rommon 12 > xmodem -c c1841-ipbasek9-mz.124-11.XJ4.binDo not start the sen...

I am looking for a Cisco switch which can be compared to Enterasys A2H124-24FX SecureStack A2 with 24 100Base-FX Ports via MTRJPhysical Ports24 100Base-FX MTRJ ports2 SFP GBIC ports2 10/100/1000 ports for uplinks or stacking ports1 DB9 console port1 ...

All, Im trying to do the following, without success at this point. I have a laptop, 3560 switch, and ACS v3.3. I have the port my laptop is plugged into to do dot1x. If you login fine, you get on the trusted network. If not, you get dumped into t...

Dear Experts ,Please find the attached network diagram.we want to do load-balancing between E1's which was mentioned in the diagram.Generally , how to achieve load-balancing using HSRP ?I know we can go for MHSRP ,, but we do not want to use MHSRP.An...

Hi!I would like to send all events to begin with. But the Eventsmanager doesnt get any syslog activity. Is there other steps i need to do on the switch other then ->Logging myhostname?If i want to monitor almost every event is default settiing good f...

do i need to add it as a client mode or transparent than to to server mode,but i think as transparent the switch does save the vlans10xs

i want to know if there is a more simple way to alow VPN trafic on a vlanthe way i'm dooing it now is just alowing varius ports depending on what is neededand that can lead to some trouble because when i get a user that has a different cliend/port i ...

I need my 6500 VSS supervisor - VS-C6509E-S720-10G to support an IPT network (QOS features, etc). What IOS should I be going with?IP Services, Adv Ent Services, IOS Adv IP services or advanced enterprise services?

I have a question of QoS trust behavior, I am not sure if what I remember is correct.If I config mls qos trust cos, what will be done for dscp? will the dscp be remarked with the config of "mls qos map cos-dscp"? and for mls qos trust dscp, will the ...

Hi allIs there any situation i would configure a layer 2 Vlan at the distribution layer. I am using layer 3 sw at the distribution layer. If yes , may i know the reason for doing that.What i usually do is to configure layer 2 vlan at teh access switc...