Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...

IMG_1447.jpeg IMG_1448.jpeg IMG_1446.jpeg
amnavada by • Cisco Employee
  • 18333 Views
  • 36 replies
  • 2 Helpful votes

Good afternoon,   Having an issue with VTP propagation.  I have two 2950 switches, Switch_1 as VTP server and Switch_2 as VTP Client and both fa0/23 ports are configured as trunks.  Switch_1 has four Vlans (vlan 1, vlan 10, vlan 20, vlan 30) but they...

paquinjrm by • Community Member
  • 1166 Views
  • 3 replies
  • 0 Helpful votes

I have a C9500-48Y4C IOS XE 17.12.4 that is notifying of a lot of MAC flapping. This is the typical error log. Oct 27 13:14:41.253: %SW_MATM-4-MACFLAP_NOTIF: Host 0050.56b1.96a0 in vlan 412 is flapping between port Twe1/0/3 and port Po1When the switc...

rlwilson by • Visitor
  • 3660 Views
  • 7 replies
  • 0 Helpful votes

Good day pros,Two week a go, was trying to upgrade  Cisco C9200 (STACK2) switch from IOS cat9k_lite_iosxe.17.12.06.SPA.bin to cat9k_lite_iosxe.17.12.08.SPA.bin. It was successfully uploaded and I changed the boot variable. (As I did upgraded many sta...

Is there a way to check basic Meraki switch hardware health metrics? Unit temperature, fan speeds, any internal failures?The "device health" tab seems to only expose some hardware statuses (CPU: good / poor; memory: good / poor, etc.) - but I see no ...

kindzma by • Level 4
  • 562 Views
  • 7 replies
  • 1 Helpful votes

Hi all,Yesterday I upgraded two Cisco 9500-40X switches from IOS-XE 16.6.9 to 17.18.4 and configured them in a StackWise Virtual setup.In my previous experience with the Cisco C9500-48Y4C-A, the standby switch's console port became unavailable for co...

marzi by • Level 4
  • 223 Views
  • 3 replies
  • 0 Helpful votes

Hello, our 9200 switches with code 17.9.4a receives dacl from ise and authorize clients successfully. Based on the complaints (endpoint can access to destinations that they shouldn’t as destinations not allowed in DACL) we started to see if anything ...

tungrwaga58 by • Community Member
  • 1251 Views
  • 6 replies
  • 0 Helpful votes

Can anyone explain why a burned-in MAC address might deviate from the logical numbering scheme? Typically, the MAC addresses for a switch’s ports begin with a base MAC address and increment in sequence, corresponding to the port numbers. In our case,...

Tec1do by • Community Member
  • 1948 Views
  • 28 replies
  • 2 Helpful votes

Hello, everyone! I'm new here and just have, still, a very basic knowledge of how to use Cisco Packet Tracer. I'm really trying my best to learn, but I got into this problem, and I feel like I don't know what to do anymore. Just really hoping someone...

redtamaraws_0-1737408897059.png
redtamaraws by • Community Member
  • 2235 Views
  • 5 replies
  • 0 Helpful votes

Hello i just started a QC position at my job with minimal training wanted to see if there was and emulators or thing of that nature to test ports extremely new to this working with switches for cisco would gratefully appreciate any info tips thanks.

TXFloater by • Community Member
  • 275 Views
  • 5 replies
  • 0 Helpful votes

I bought a Cisco Catalyst switch from a hamfest (amateur radio swap meet) and am trying to get it working.  I am a retired software engineer and am just looking to get this working.  I can connect to it through a serial conection and can run some ini...