Unity 11.5 data export COP

[Remington]

I am trying to find the correct download for the Unity 11.5 COP file to enable "utils system upgrade dataexport initiate". I attempted to install the file from ciscocm.DataExport_v4.0.zip, but am getting an error message saying, "This cop file is not applicable on this product (connection)." Any suggestion? Thanks. 

[Jaime Valencia]

The README explains this, did you review it?

Important Note:
1. The v1 DataExport COP files (ciscocm.DataExport_v1.0.cop and
ciscocm.DataExport_rollback_v1.0.cop) are installable on source releases from 10.5 to all pre 14 UCM
releases.
2. Since “Fresh Install with Data Import” feature is now supported on 12.5SU5 UCM release, v2 COP files
are available (ciscocm.DataExport_v2.0.cop and ciscocm.DataExport_rollback_v2.0.cop) which are
installable on source releases 10.5, 11x, 12x up to 12.5 SU4.

Installation Instructions:
As with any installation or upgrade, it is recommended that you apply this Update during off peak hours.
Install the cop file on the Cisco Unified Communications Manager and Cisco Unified Communications
Manager IM and Presence only.

https://www.cisco.com/web/software/286319173/139477/ciscocm.DataExport_v4.0_Readme.pdf

The CUC documentation covers the upgrade options, and this one is not listed as one, your options are DRS or COBRAS, have you reviewed the Install, Upgrade and Maintenance Guide for Cisco Unity Connection guides? if not, that's your first step.

[Shalid Kurunnan Chalil · Accepted solution]

Hi @Jaime Valencia 

I found another read me file where it state that it can be done on CUC  

as per the read me file on the unity connection COP-File folder https://software.cisco.com/download/home/286328409/type/286319537/release/COP-Files It states that the data export can be installed on the CUC 

https://www.cisco.com/web/software/286319537/139787/ciscocm.cuc_DataExport_v1.1_Readme.pdf

Am I looking this wrng? 

Regards

[Shalid Kurunnan Chalil]

Hi @Remington ,

Could you please share the output of the "show version active" and "show version inactive" from your CUC CLI?  also it would be great if you could extract the install log file as it may contain additional information about the error. 

Regards

[Remington]

I installed the COP file you had linked in this post, and it was what I needed. Thank you.

admin:show version active
Active Master Version: 11.5.1.23900-30
Active Version Installed Software Options:
ciscocm.cuc_DataExport_v1.1.k4.cop
admin:

[Nithin Eluvathingal]

Your actual problem was that you were trying to use the COP intended for CUCM. For the CUC, there is a different COP to export the data. The one you used Now is the correct one, and that’s why it went through.

[Remington]

Yes, I understand that. @Jaime Valencia highlighted that in the readme and @Shalid Kurunnan Chalil provided a link for the COP I needed.

[Remington]

I did not, I was using documentation from a consultant. I will follow up with them.
Thank you for informing me. 

[Nithin Eluvathingal]

I’ve used this option to export the CUC data three to four times. I prefer this method for CUC because PCD doesn’t support migrations. The command should function properly if you’re using version 11.5 or above. The cop file used is ciscocm.cuc_DataExport_v1.1.zip.

Could you please tell me your CUC version?