Can Intersight CVA be configured for high availability?
-
Buying Recommendation
(18) -
Call Control
(1) -
Cisco ACI
(2) -
Cisco Bugs
(2) -
Cisco Cafe
(5) -
Cisco Intersight
(1) -
Cisco Software
(1) -
Cisco.com Idea Center
(1) -
Collaboration Endpoints
(1) -
Collaboration Solutions
(2) -
Community Feedback Forum
(6) -
Community Ideas
(5) -
Conferencing
(1) -
CSC Content with No Valid Community to Post
(1) -
CUCM
(1) -
Data Center
(2) -
Data Center Networking
(1) -
HyperFlex
(142) -
Identity Services Engine (ISE)
(2) -
ISR 4000 Series
(1) -
LAN
(1) -
LAN Switching
(3) -
Network Management
(2) -
Online Chat Support
(1) -
Other
(1) -
Other Collaboration Applications
(7) -
Other Collaboration Topics
(3) -
Other IP Telephony
(2) -
Other Networking
(1) -
Other Switches
(2) -
Other Switching
(4) -
Other Unified Communications
(12) -
Other Unified Computing System
(699) -
Routing
(1) -
Server Networking
(1) -
Small Business Network and Smart Storage
(1) -
Small Business Routers
(1) -
Small Business Support Service
(1) -
Storage Networking
(1) -
Switching
(1) -
UC Applications
(8) -
UC Migration
(1) -
UCS Advantage Series
(9) -
UCS Central
(62) -
UCS Director
(19) -
UCS Manager
(392) -
UCS Networking and Storage
(193) -
UCS PowerTool
(48) -
UCS Solutions
(152) -
Unified Communications
(16) -
Unified Computing
(2) -
Unified Computing System (UCS)
(6,563) -
VDI
(3) -
Voice Gateways
(1) -
Wireless LAN Controller
(1)
- « Previous « Previous
- Next » Next »
Forum Posts
We have a HyperFlex Edge cluster with 2 nodes. We don't use HyperFlex Edge nor do we manage the nodes via Intersight. Interestingly enough, the HyperFlex web portal for our hosts shows it is tied to an account. We do utilize these hosts for our Cisco...
This morning, we are seeing that UCS cluster IP is not accessable over HTTP but it was pinging also we are not able to do SSH to any of the IP address(2 FIs or cluster IP)
Hello, Our customer has UCS 6332 in a cluster. We would like to know if it is possible to Connect HA FortiGates directly to Cisco UCS 6332 using LACP Aggregate interfaces and Virtual Port Channels (vPCs)(full mech)? Thank You
Hello,i recently got my hands on a Tesla P40 GPU that I would like to use in my C460 M4.The power connector has caused me a lot of confusion.as I understand it, the Tesla P40 makes use of a 12V EPS connector.the connector on the PCIe riser board also...
Hi there, I have been doing an extensive search regarding the compatibility of Cisco B-series servers with Nutanix, and I've found that it used to be compatible with B-Series M4 only, but now it's reached its EOL (https://portal.nutanix.com/page/docu...
Hi All, We keep getting the error detailed attached when trying to install ESXi 7.0.3 on Cisco UCS C220M7N even after upgrading the latter one to the most recent CIMC version 4.3(3.240043) using ucs-c220m7-huu-4.3.3.240043.iso. Has anyone seen the sa...
Im a bit at a loss. I have and older ucs system with b200 m5 blades. I am reusing those blades in a whole new environment due to hardware refresh. The new environment is managed via IMM only and there is no UCSM.When i go to deploy my newly created S...
Hi All When migrating from UCS fabricInterConnect6296 to UCS fabricInterConnect64108,When migrating from FI A: Primary / FI B: Subordinate to FI A: Subordinate / FI B: Primary (connect local-mgmt to FI A and execute “cluster lead b” ), and then perfo...
After upgrading UCS 220 M5 from 4.0(4b) to 4.3(2.230270) I can no longer ping the CIMC IP addresses outside of the current network. I can SSH to them from the VLAN and confirm the gateway is there. I had power cycled one for 10 minutes and it still i...
Hi all, I was after some help with one of my servers. It's been with TAC since mid-March but I'm not getting anywhere. Initial symptoms were - P_CATERR_N thrown in BIOS with server freezing - Cisco recommended firmware update - no fix - Cisco swapp...
Hi Folks, we are migrating UCS B-series servers from old Fabric Interconnects to new ones. Both the environments are managed by UCSM and use native fibre Channel. As part of the migration, we want to maintain the same WWPN on the vHBAs as the previou...
Hello,Most of the information is in the title. I have connected the Tintri device with the sfps that came with it, and tried SFP-10-SR-S, DS-SFP-FC8G-SW, DS-SFP-FC16G-SW= on the end that is connected to the FI. I added the VLAN to both LAN->LAN Cloud...
Good day, I have a Cisco UCS C240 M5S in which I am attempting to load a copy of Windows Server on. I can boot from the USB drive in Legacy Mode with no problems, yet I cannot find a proper controller driver so that I can see the installed drives/vol...
I upgrade ucs from 2.0.2x to 4.0.4 everything is fine , but After I click acknowledge reboot primary FI, all blades on 10 9 chassis rebooted at same time, and pass long time rediscover time, we lost all bussiness for 2 hour, because we need time to ...