We got a defective UCS blade B200 M3 equipped with E5-26xx V2 processors. We also have a replacement blade server but with V1 processors. So we took the good V2 processors from the defective blade and put them into the replacement server...Now comes ...
Forum Posts
Upgraded to firmware 4.1.3(m) a few weeks ago and started to delete what was believed to be unreferenced firmware.Deleted all old A and B firmware packages including ucs-catalog, and then noticed a few hundred major faults such as these below:storage...
Hi all, I’m running a Cisco HyperFlex cluster with HXAF240C-M6SN nodes (UCSC-C240-M6SN servers), and I’m currently using the following NVMe drives: Intel P5500 – 3.8TB U.2 NVMe Part Number: UCS-NVMEI4-I3840 I want to expand the NVMe capacity and ...
Hello,I want to find the total power consumption of an UCS server ( UCS managed and standalone) from within RHEL and from FI. Can someone advise on that? Thanks
I recently got my hands on a Cisco C240 M4SX with 24 drive bays. It’s equipped with a Cisco 12G SAS Modular RAID Controller, but I’ve run into an issue I can’t seem to solve.From what I’ve read, using a non-Cisco PCIe adapter causes the system fans t...
Looking to add an additional NIC Card to the UCS BE6M-M5-K9 server. Has anyone done this that can provide some guidance.
Resolved! Can UCSX be managed without intersight?
Hi All, I want to know about can UCSX be managed without intersight, just like B series be managed by UCSM on FI? And if UCSX has already been managed by Intersight, can it be converted to manage by UCSM?
I have a Cisco ISE SNS-3655-K9 with CIMC vC220M5.4.3.2a.0_ISE. After uploading a public certificate to get rid of the certificate error when accessing the GUI of the CIMC, everything works, except when I try to look at the certificate or navigate to...
Hi All, I wonder , if there 4 fc uplinks on each FI A and FI B (no port-channel), there are 2 vhba on each blases and goes to FI-A and FI-B, no config pin group. If there is fc uplink down, the vhba pin to the down port will be repinned to other av...
Resolved! UCS Firmware update to Chassis
We are preparing to upgrade our Chassis to 4.1.3m after a previous update to the fabric interconnects and currently have two critical errors:1. FSM:FAILED]: Update identities to external identifier manager(FSM:sam:dme:IdentIdentRequestUpdateIdent). R...
increase KVM timeout in UCSM. Is there a way to increase the KVM timeout. The problem I am experiencing is that when I have the KVM running and it is idled for couple of minutes it will log out. I want to increase that timeout. I was able to incre...
We have UCSM 4.2(3j), and backups are failing to a remote Linux box.We have the following error codes in the UCSM
Resolved! Firmware upgrade from 3.2(3) to 4.1(3m)
I have done all of the system health checks and started the firmware upgrade, but seem to have gotten stuck while doing the fabric update. The web interface is down, but when I cli to fabric a and b, they both show the updated version of 4.1(3m).What...
Hi!We had a broken disk on our cisco ise server which is setup using Raid 10.Went out with a new disk same size and everything but different brand, Seage instead of Thosiba BUT everything else is indentical.The disk shows up fine in CIMC, but says Un...
UCS manager firmware upgrade is not working. All UCS B200M3 servers are running version 4.1.3nb, but the chassis I/O module and fabric interconnect are not upgrading.
