Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
ahmad_tamneh
‎05-14-2021
Enthusiast
Personal Website
Recent Badges
Awards
Recent Badges
See all
100 Helpful Vote
1 Project Story
30 Helpful Vote
50 Replies
CCP Member
10 Helpful Vote
1 Helpful Vote
1 Accepted Solution
20 Replies
10 Replies
Stats
Member since ‎08-05-2008
89
Posts
85
Helpful
2
Solutions
Certifications
Cisco Certified Specialist - Data Center Core
Cisco Certified Specialist - Data Center Core
Cisco Certified Specialist - Data Center Core
Cisco Certified Specialist - Data Center Core
Cisco Certified Specialist - Collaboration Core
Cisco Certified Internetwork Expert Collaboration (CCIE Collaboration)
Cisco Certified Specialist - Collaboration Core
Cisco Certified Internetwork Expert Collaboration (CCIE Collaboration)
Cisco Certified Specialist - Collaboration Core
Cisco Certified Internetwork Expert Collaboration (CCIE Collaboration)
Cisco Certified Specialist - Collaboration Core
Cisco Certified Internetwork Expert Collaboration (CCIE Collaboration)
Cisco Certified Specialist - Collaboration Core
Cisco Certified Internetwork Expert Collaboration (CCIE Collaboration)
Cisco Certified Internetwork Expert Collaboration (CCIE Collaboration)
Cisco Certified Internetwork Expert Collaboration (CCIE Collaboration)
Cisco Certified Network Associate Routing and Switching (CCNA Routing and Switching)
Cisco Certified Network Associate Routing and Switching (CCNA Routing and Switching)
Cisco Certified Network Associate Routing and Switching (CCNA Routing and Switching)
Cisco Certified Network Associate Routing and Switching (CCNA Routing and Switching)

Phone url not working

Created by in IP Telephony and Phones
05-24-2011
05-24-2011
Hi all,I have this case, I have 2 systems, one with CCM 5.1.3g,which will be migrated to new system ...

Re: IPCC express disable call forward all restriction

Created by in Contact Center
04-26-2011
04-26-2011
Hi,you may also use CFW ALL Calling search space with no access to any partition

Re: FXO 4 Voice Ports always up (busy)

Created by in IP Telephony and Phones
04-22-2011
04-22-2011
Hi Ali,Well, as beginning you have to try using the cptone SA under the voice port , some times it w...

Re: FXO 4 Voice Ports always up (busy)

Created by in IP Telephony and Phones
04-21-2011
04-21-2011
There is a frequency used with the FXO port to allow it detect the Disconnect signal,you need to fin...

Re: it takes Long time to save any device related config

Created by in IP Telephony and Phones
04-17-2011
04-17-2011
Hi clileikis,Yes I can say it happened most of the time, we did not reboot the call manger recently

Re: it takes Long time to save any device related config

Created by in IP Telephony and Phones
04-17-2011
04-17-2011
Hi Paolo,mm you can say that in the bad cases it may take more than minute ..now specific ?

Re: it takes Long time to save any device related config

Created by in IP Telephony and Phones
04-17-2011
04-17-2011
Well, Amer you are right, I checked earlier the speed between the switch and the CUCM, but the stran...

it takes Long time to save any device related config

Created by in IP Telephony and Phones
04-17-2011
04-17-2011
Hi,I have a strange behavior with my CCM 6.1.3.3201-1, when you try to save any changed on the devic...

Re: How to check the cluster on the CUCM

Created by in IP Telephony and Phones
04-12-2011
04-12-2011
You can check it from the CUCM unified reporting :Unified CM Database Status -->Unified CM Database ...

Re: Caller Name on CME

Created by in IP Telephony and Phones
04-10-2011
04-10-2011
Hi All,I solve the the problem.. by defining Intercluster-Trunk.. instead of normal GW..

Caller Name on CME

Created by in IP Telephony and Phones
04-07-2011
04-07-2011
Dear ,I have CME 8.1 and CUCM 6.1, I define the CME as H.323 VG on the CUCM, and I configure a Voip ...

outbound is not working-sccp dialer

Created by in Contact Center
04-06-2011
04-06-2011
I have configure the sccp dialer, and I was able to make a successful campaign, but now I am not abl...

Re: outbound option - direct view

Created by in Contact Center
02-24-2011
02-24-2011
and here attached the output of the call tracer.

Re: outbound option - direct view

Created by in Contact Center
02-24-2011
02-24-2011
How test the dialer, just to put the diallist on the import path,The call now is disconnectedattache...

Re: outbound option - direct view

Created by in Contact Center
02-24-2011
02-24-2011
You may right click the image and click save target as:and now i have the following issue.. the dial...
Public Statistics
Date Registered ‎08-05-2008 06:55 AM
Date Last Visited ‎05-14-2021 12:35 AM
Total Messages Posted 89
Total Helpful Votes Received 85
Helpful Votes Given To