About balaji.bandi

balaji.bandi · 11-06-2019

Hello support i am not sure iam the one who facing the issue, but i checked same time on mobile i see the same time i am based at +0:00 BST - around 8 am to 9 am between the community site losing the connection in the middle of my comments, and a...

balaji.bandi · 10-19-2018

Looking to deploy in production environment, Default Catalyst 9300 ship with Everest-16.6.3 ED. what is the difference here - which one got more advantage, i know Everest is the answer, if that is answer Why Fuji ?

balaji.bandi · 06-29-2018

HiWe are doing some PoC for the zero touching using APIC-EMSome of our 3750X have 2 different IOS in the stack.Master and Standby ( 1 and2 have IP Services)Memembers (3 and 4 - IP base)in this case how are we going to provision and update the IOS,I ...

balaji.bandi · 12-23-2014

Hi All I have Phone Cisco 7941G, iam try to upgrade i mess with that phone i believe, now screen is blank I have followed the below steps :1: Disconnect the computer from your Network and Connected to Different Switch, where Phone and PC Only connect...

balaji.bandi · 05-20-2013

HiIam trying to intall CUCM 8.6 on Vmware 9i get installation fail, I have attached screenshot for your referencewhat iam doing wrong ? is this possible to intall Windows 2008 R2 and Vmware 9 workstation ?any advice will be helpfull to solve my issue...

balaji.bandi · 08-12-2022

add below : ip route 0.0.0.0 0.0.0.0 10.227.113.129 from router you should able to ping 10.227.113.129, and also 8.8.8.8 before you go next level still issue make sure you post below output : show run show ip route show ip interface brief

balaji.bandi · 08-12-2022

we need to see the configuration also, you mentioned you pulled the cables from ASR1 (which one is ASR1 in your config ?) how about external side - is the eBGP still up ? (since you pulled only Lan side rigt ?) VSS switch act as Layer 2 ? you have OS...

balaji.bandi · 08-12-2022

i do not see your routing to outside ? from router are you able to ping outside 8.8.8.8 ? you need to add default route towards ISP - ip route 0.0.0.0 0.0.0.0 10.227.113.X (X is ISP side IP) Also for testing remove ACL In from outgoing intercace. i...

balaji.bandi · 08-12-2022

if that is access port - then -spanning-tree portfast should be good enough.

balaji.bandi · 08-12-2022

You have NAT config on the interface : interface Vlan3ip nat outside!interface Vlan2ip nat inside ! interface Vlan1ip nat inside

Member Since	‎05-19-2013 11:51 PM
Date Last Visited
Posts	24,850
Total Helpful Votes Received	24569

User Statistics

User Activity

Community site keep loosing the connection - it take 3-5min(some time more) to come back every day

Fuji-16.9.1 ED Vs Everest-16.6.3 ED

APIC-EM - with different IOS PnP

7941G Phone Screen Blank. Not able to Upgrade the Firmware

CUCM 8.6 Installation on VMWare Workstation 9.X On windows 2008 R2

Re: 1:1 Static NAT, shouldn't this be simple ISR C1121-4P

Re: Does DR/BDR role affect OSPF convergence time?

Re: 1:1 Static NAT, shouldn't this be simple ISR C1121-4P

Re: spanning-tree portfast edge invalid input on 9200 switch

Re: 1:1 Static NAT, shouldn't this be simple ISR C1121-4P