Hi,   Silly question but never installed PCCE before. Is there specific install media for this or do you use the usual UCCE Install media?   I see in the PCCE guides it says when you get to Web Install it does validation checking which I obviously don't get with the normal UCCE media   I need to get this installed as soon as possible but only have UCCE install media. How far can I get?   TIA   ... View more

Hi,   Jsut wondering whether this document is still valid for UCCE/PCCE 11.6 with Windows 2012?   https://www.cisco.com/c/en/us/support/docs/servers-unified-computing/ucs-manager/116092-vmware-deploy-cklst-ucce-00.html   I do not see mention of doing any of this config in the PCCE install guide & this doc is 6 years old.   Cheers ... View more

Hi,   I have some B200M4 servers running on UCS version 3.2(2b) with Cisco VIC 1340s. I have just installed the Cisco custom image for ESXi 6.5 U2   On checking the installed drivers vs the "supported" drivers on the UCS Hardware and Software Compatibility portal I noticed that nenic & fnic drivers that were installed with the Cisco custom image are a few revisions higher than what is in the portal.   Can I assume that the portal is outdated.....or do I need to downgrade my VMware drivers?   NENIC installed - 1.0.25.0-1OEM.650.0.0.4598673 NENIC portal  - 1.0.16.0   FNIC installed - 1.6.0.44 FNIC portal -1.6.0.37   Thanks in advance ... View more

Hi,   Having a strange issue on a new setup that I can only assume is something so simple I've missed it   I have a 4431 CUBE with Security licensing which I need to convert TCP/RTP to TLS/sRTP before sending through a firewall and out to the internet I have configured 4431s with TCP/TLS interworking before so I have known working config to reference though have always done it with UCM to CUBE as TLS and CUBE to ITSP as TCP. This callflow is Ingress 2921 GW (TCP)--> 4431 CUBE (TLS)--> Firewall --> Internet   The issue I have here is I am receiving the TCP invite (from ingress GWG) and my 4431 sends back the Trying but it never sends the Outbound TLS invite at all. My dialpeer config is correct because If I change my outbound dialpeer to TCP it works. For some reason my 4431 will not initiate an outbound TLS invite at all   Below is the relevant config I believe   ! dspfarm profile 1 transcode universal    codec g711alaw  codec g711ulaw  codec g729r8  maximum sessions 40  associate application CUBE ! dial-peer voice 1 voip  description FROM INGRESS GW  translation-profile incoming GW-IN  session protocol sipv2  session transport tcp  incoming called e164-pattern-map 100  voice-class sip bind control source-interface Port-channel1.402  voice-class sip bind media source-interface Port-channel1.402  dtmf-relay rtp-nte  codec g711alaw  no vad ! dial-peer voice 2 voip  description OUTBOUND  translation-profile outgoing OUTBOUND  session protocol sipv2  session target dns:abc.com  session transport tcp tls  destination e164-pattern-map 100  voice-class sip bind control source-interface BDI403  voice-class sip bind media source-interface BDI403  dtmf-relay rtp-nte  srtp  codec g711alaw  no vad   THe only think I can think of is that 5061 is not open on the far end yet.....but the 4431 should still at least send the Invite right? ... View more

Hi, Have a UCCE Compreshensive setup with CUSP. We are testing a SIP Refer from a script using the "rfxxxxxxxxx" in a label.   The Refer is working but NOT if the ingress POTS dial peer has the servicability service assigned to it. Call goes into survivabilty mode. Remove the survivabilty from ingress POTS dial peer and refer works perfectly.   CVP/UCCE 8.5 Ingress gateway 2921 - c2900-universalk9-mz.SPA.152-2.T2.bin   Call Flow E1 --> 2921 --> SIP --> CUSP --CVP/UCCE --> REFER --> CUSP --> 2921 --> E1   I can see that gateway attempts the call back to the PSTN after the refer but then survuvabilty kicks in. Just want to see if this is a known issue or someone has seen this before I open a TAC   Thanks ... View more