Resolved! CCA 2.1 Supported Feature List
I have heard that Cisco is building a list of "supported features" for CCA 2.1 that clearly outlines what can or can't be done in CCA vs CLI. Anyone know where I can find such a list?
I have heard that Cisco is building a list of "supported features" for CCA 2.1 that clearly outlines what can or can't be done in CCA vs CLI. Anyone know where I can find such a list?
Hi Guys,Just upgraded to CCA 2.1 and was going to upgrade to the new EA release to support the new SPA504 phones i have arriving today.But, under the Maintenance tab, all the options are missing except File Management. No upgrade option or the new ph...
I have read the section of the SBCS administrator guide which describes octo lines. The SBCS guide mentions that analog FXS ports, and 7920, 7902, 7931G, CP-52xG, CP-52xSG, SPA525G phones are not octo-line capable. I have not seen in the documentatio...
I'm using SPA3102 with Gizmo5 SIP VoIP service currently without any PSTN connectivity. Outgoing calls are very fine. However, incoming calls are very unreliable, like only occasionally the attached analog phone rings. It's not a total no-ringing-at-...
I am trying to get the multi-level AA working on my UC 500I have a base AA at ext 298I configure option 3 to send to submenu1This submenu appears to be created as 2981But when you call 298 opt 3 you get dead air for about 10 seconds then disconnec...
My SPA8800 has firmware 6.1.7 (GW). The Quick Start Guide lists an IVR Action # 201 for setting the device mode for Router/NAT or Bridge/Switch. The IVR however reports this option to be invalid. Web interface does not have the option either. I would...
Hallo,got a SPA3102 and everything works fine if I only use Line 1. When I change the Dial Plan from (xx.) for example to (<#,:>xx.<:@gw0>|xx.) all outbound calls over Line 1 work until I make _one_ call out over the PSTN. After that I can not reach ...
Hello, VoIP to PSTN works only after a fresh hard reboot of my SPA310. It works once and after first call it stops working. I tried with no pin and with pin. I tried factory reset. I tried every thing basically. Thank you in advance.
Hello all,I am currently trying to upgrade my UC520. The IOS I am attempting to use is 12.4(20)T2. When I go into CCA I see the UC520 and the phones attached however when I attempt to configure anything throught he "voice" option I receive an embed...
Device does not get a reply to its Notify Keep alivecan easy be re produced on 2102 (5.2.5) by truning on Notify for NAT keepalive and setting outbound proxy an IP not send back ICMP errors1/2 1 2 4, 4,4 second Register retry cycle is repeated eve...
Hi, i have over 100 SPA901 phones in hotel and two of them now blinking SOS recovery. Where I can find recovery utility with firmware and simple how-to recover firmware in SPA901? Thanks.
Hi, we have a few types of IP phones deployed in the field. Currently we're experiencing a problem with a Planet VIP-103PT phone calling a Cisco SPA922 phone:When a Planet VIP-103PT initiate a call to a Cisco SPA922 (firmware 6.1.5a), upon answering...
Hi,I have a SPA508G running software 7.1.3. However it only seems to have 4 configurable extn's. I was expected 8 extn's on the 508G as it has 8 line keys. Is this a software bug? Thanks.
This is probably an easy one but I have not been able to figure it out.I have 2 PSTN lines going into a SPA400 that is connected to a SPA9000. I want 2 separate auto attendants to be active, one for each line.Is this possible?
I wish to provide QoS best practice by configuring seperate VLANS for data and voice. I am using the SRW208P switch. With the 7940 IP phone and a catalyst switch one would trust CoS and trust device cisco Phone and configure an Aux VLAN at the switch...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: