VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

We have set  up a VPN between an ASA 5505 and a 1751 router .That vpn has to replace a previous one between the 1751 and another router .The VPN is established successfully and I can ping the 1751's internal interface from the ASA's network, but I ca...

s_colombo by Level 1
  • 578 Views
  • 3 replies
  • 0 Helpful votes

I am getting the following error message from two devices on my network:CRYPTO-4-RECVD_PKT_MAC_ERR: decrypt: mac verify failed for connection id=<removed> local=<removed> remote=<removed> spi=F1E30F16 seqno=0000905DCisco decodes the message as:%CRYPT...

I'm trying to set up a VPN between anASA 5505 and a Cisco 1751 router.So far we're having problem witha ISAKMP which cannot establish SA .On the 1751 router I can find the following errorMar  9 01:18:38.804: ISAKMP (0:103): incrementing error counter...

s_colombo by Level 1
  • 526 Views
  • 1 replies
  • 0 Helpful votes

Hi,I have a router with crypto map applied to an interface.  This crypto map has two remote peers with the below configuration.crypto map test 10 isakmp-ipsecset peer 1.1.1.1set peer 2.2.2.2set transform-set tsetmatch address 101access-list 101 permi...

i attempted to change the admin password from the default of user: cisco, pass: cisco by using the following command from the terminal command line:  hostname(config)# enable password (new password) encrypted once the command was entered and i wrote ...

tmercer12 by Level 1
  • 1963 Views
  • 5 replies
  • 0 Helpful votes

Hi All,Does NAC supports Out-Of-Band for VPN? I want to deploy the NAC 4.7 for VPN users. Is it possible to deploy NAC OOB for VPN users?Regards,Vashdev

vashdevt by Level 1
  • 525 Views
  • 1 replies
  • 0 Helpful votes

A password policy has been applied on windows domain that requires users to change passwords x # days.Our ASA remote access VPN authenticate against the domain.The users are not being prompted to change their passwords using their client VPNs, the co...

westcare by Level 1
  • 800 Views
  • 3 replies
  • 0 Helpful votes

Hi all,I have a site to site vpn setup between country A and country B. We are using cisco pix515e on both sites. In country A our cisco pix515e is connected to 3 networks, office(192.168.x.x), dmz(172.16.x.x) and external. With the site to site vpn ...

mmitgroup by Level 1
  • 457 Views
  • 1 replies
  • 0 Helpful votes

Hi,    If i have a vpn concentrator setup in the following manner...Internet |Router |VPN concentrator |Distribution Switcha) Will i be able to see the vpn concentrator ip when i tracert from the Distribution switch to the router ( assuming no acl's ...

Hi!I have two Cisco ASA 5505 and S2S VPN tunnel, when tunnel is down( no more traffic,rekey) I have no access to local network of another site until somebody from another site pings my local network, but at the same time "show crypto isakmp sa" and "...

ToX1c1986 by Level 1
  • 1700 Views
  • 2 replies
  • 0 Helpful votes

Hi,Have users connecting into ASA, and they are required to enter Group+Shared secret, but then also a username+password(Which we have added as local accounts on the ASA) - Is there anyway to have just Group+shared secret auth?Thanks in advance

I want to have my Cisco 1841 open a VPN connection to a remote site using IPsec with a shared secret and a username/password, and route only certaintraffic through this virtual connection. From an IP standpoint, I want the router to act as a client, ...

simonwynn by Level 1
  • 1504 Views
  • 2 replies
  • 0 Helpful votes

using Win7? you'll be happy to learn about this new beta that Cisco released and allow Win7 64-bit vpn client installationdid anyone try it?http://ITDualism.wordpress.com

ofir by Level 1
  • 4812 Views
  • 2 replies
  • 0 Helpful votes
Top Solution Authors