VPN

Does anybody knows where to get detail infot about "how to configure OSPF on a VPN Concentrator"? I?ve been spending lots of time configuring it without any "luck"....!!!Best regards,

Hi.I have 2 VPN 2005. I need to put the concentrators an a DMZ lan protected by a checkpoint firewall that do nat.I issigned ip address foreach vpn device on private lan, and none for public. Because checkpoint do nat for vpn concentrators, i cannot...

Hi.We have a problem with an idle-timeout witch a 3640 (ios release 12.2(40).It seems that idle-timeout timer is non cleared, so when it reach configured timeout it bring down call.Configuration of int dialer is:int dialer100 ip address negotiated ip...

HiI have used a VPN3030 concentrator since 4 years in a classical way: 1 public interface (for Lan-to-Lan IPSec and remote-acces (NAT-T)connections) and 1 private interface.I need to connect to an external (not internet) network and offer Remote-acce...

Our firewall appliance is a Cisco ASA-5510. I manage many HP thin clients. They come with RDP built in, which is a useful admin tool in certain situations. Unfortunately I can't block certain users on the thin client from using RDP, as the only wa...

I will post more data once back in the office but this is the error my VPNC3000 is showing when the IPSec tunnel tries to establish:I've replaced the PIX 501 outside IP with 10.0.0.1, and the concentrator subnet with 10.1.0.018890 04/04/2007 15:09:33...

Q. For some reason I am unable to ping past my peer (head end) on my EzVPN connection. Below is a copy of the 871W config, and test results. Please let me know if you see something that stands out which may be preventing me from passing traffic.

I have 1 router cisco 1812 whit real IP on Ethernet 0/0 and my ISP give up 40 Mbps.Can I use Ethernet 0/0 for VPN whit IPSec for my 10 remote office whit "shape" on 1Mbps. Is it posible for 1812 whit 3DES and ESP.

I have a ipsec tunnel from HQ to a Pix 501. The tunnel works perfectly. I'm trying to add connectivity from another subnet in HQ to access the Pix over existing tunnel. Can someone point me to some documentation or list the commands necessary to imp...

I have a VPN 3015 concentrator and I am using the Cisco VPN client (v4.8). I am using Active Directory to authenticate users. I recently noticed that I can use any qualifier with the correct username/password and I will authenticate to the concentr...

I have successfully created a site to site vpn between two Cisco 857 Routers and can ping all available equipment at each end.Having done this I am still unable to log on to a domain from the other end of the vpn and get a message that the RPC server...

I recently updated about 70 routers from preshared key to certificate authentication. The most part of them works fine but I'm still searching to resolve a problem on 3 of them.When I use preshared key the isakmp and ipsec phases complete successful...

Hi All,I've got 3 offices linked together with IPSec tunnels running on 2811 Routers.I need to configure this so that from the two branches, the default route is down the VPN tunnel to the Main site, rather than out to the internet.I traied configuri...

Hi,I have configured a Cisco ASA-SSM IPS module in a Cisco ASA 5510, and am having issues whereby users on the inside can initiate a VPN session to an outside host, but cannot bring up an RDP session within the VPN session. When I remove the IPS ins...

Greetings,I'm attempting to limit access to network resources across a VPN tunnel but can't seem to get it right. Here's the situation...Network resources:1 Terminal Server (OKATERM1)2 DC's + DNS (OKAMAIN1 & OKASQL1)I want to allow DNS requests to t...