Dear sir, Do you have any idea how to perform this task? We've setup Ciscoworks VMS, how to access the ciscowroks vms through web browser internet explorer?
Dear sir, Do you have any idea how to perform this task? We've setup Ciscoworks VMS, how to access the ciscowroks vms through web browser internet explorer?
I have a PIX VPN hub and spoke configuration and I want to let the spokes communicate with eachother. In the documentation it says "The two outlying networks are not able to communicate with each other by going through the central PIX because the PIX...
does the new pix 7.0 ios support ipsec stateful failover. i have no info abt. help urgent. thank u sebastan
Hi,I am setting up a vpn remote access solution with a ADSL Modem, a 1720 Router and a ASA. I only have one fixed Ip address on the Dialer Interface of the Router, and behind the Router I am using RFC1918 addresses. Also the outside interface of the ...
Hi,We have a unique problem with one of our vpn field office setup. The vpn tunnel seemed to be perfectly working but application, such as http, smtp and others don't work.Firewall policies between sites are properly configured and do not filter the...
Hello,Design question: I have multiple customers that will be VPNing (RA) into a single ASA. I would like to restrict their network access to a single vlan (subnet) on the ASA. Is this possible? I know it can be done w/ downloadable ACLs w/ ACS, but ...
Hi all,Here is my situation. I have several vpn clients(mobile) that connect from hotel locations and such. I also have a permanent vpn tunnel on the same interface(outside) to a remote location. I have been told by Cisco that the Pix cannot route ...
Hi all,Im trying to connect to a remote site that is protected by a PIX 501 using the cisco vpn client. I can connect to the remote site if I go through a dialup or any other dsl connection, however, I cannot connect to the remote site from our main...
I have a PIX VPN hub and spoke configuration and I want to let the spokes communicate with eachother. In the documentation it says "The two outlying networks are not able to communicate with each other by going through the central PIX because the PIX...
Hello,The following message apears on a syslog server: "%CRYPTO-4-IKMP_BAD_MESSAGE: IKE message from 10.77.77.76 failed its sanity check or is malformed". The message arrives from a router with ipsec tunnel connections. Although this message apea...
I have router 2621, PIX 515 and a windown server 2003, i want establish VPN connection from dial-up connections to windown server(with private ip) through router and PIX. How can I establish this connection? please help!
Hi all,I have a VPN Concentrator 3005 and a large number of remote workers using the 4.6 series client.None of them have any issues, except one new supplier who needs to offer remote support. They connect, their certificate is authenticated and their...
Hi, a bit of a weird setup here. We have four sites, which we'd ideally all like to go to one central site for web blocking/proxying. We're using route-maps to redirect the traffic to a squid server in the central site. It works fine in the central s...
Hi all,I have E1 links between the branch and the central sites. Now intended to backup those with AUX ports with dial-watch. When i disconnect the E1, dial-watch initiates and calls the central router and after ppp neg. connection establishes. The p...
Hi all,Look this :Mar 12 23:01:48.580 MET: %LINK-3-UPDOWN: Interface BRI0:1, changed state to upMar 12 23:01:48.580 MET: %DIALER-6-BIND: Interface BR0:1 bound to profile Di0Mar 12 23:01:48.580 MET: %ISDN-6-CONNECT: Interface BRI0:1 is now connected t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-05-2024 01:57 AM | ||
10-04-2024 02:27 AM | ||
09-30-2024 11:53 AM | ||
09-30-2024 12:54 AM | ||
09-22-2024 10:52 PM |
User | Count |
---|---|
8 | |
6 | |
2 | |
2 | |
1 |