VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

Hi All,I can set up a vpn connection using an ip pool of valid internal ip address's (ie internal network 10.10.10.0 ip pool 10.10.10.30~50). Everything works fine, access to other pc's on this subnet etc.However if i try to set using an ip pool of 1...

Dear ALL,I just received another PIX515E (UR + FO license) and as the first thing I tried to set up a small configurationbut able to start a VPN connection.As you can see I connected the outside to my LAN but I cannot establish a VPN.As VPN client I...

We are facing a problem with two PIX 515E (7.02) in failover. A network outage occurred during which all devices beyond the Pix were not available. During the time of the outage, primary PIX was not accessible via telnet and console. The secondary PI...

renju.zac by Level 1
  • 404 Views
  • 1 replies
  • 0 Helpful votes

Hi, Have a site to site VPN, the VPN phase 1&2 seam ok.Have a status QM_IDLE which is ok.Also I get a pkts no sa (send) 1 and I do get a few packets that get do get encapsulated.Is this just access-list problem?Thanks for any help.

Hi, I have a Cisco 2600 connected to a 2950. I would like to allow VPN access via ADSL to the local network via Cisco VPN client. e.gVPN Client --> ADSL Cloud --> 2600 --> 2950I have searched cisco.com and forum.cisco.com and can't find how to config...

hi everyone!I have a problem in the ACS 3.0 running on win 2000. It seems that Network Access Restrictions (NAR) under group setup configuration doesn't display after i add and fill up the content and by clicking submit & restart. I did checked the b...

I am having a problem with Microsoft VPN. we have both Microsft VPN and Cisco 3000 when the Cisco VPN client is installed ver 4.8.00 on the laptop, it disbales the Micorsoft VPN. I was wondering if possible to have both Clients configured on the lapt...

kanwar by Level 1
  • 275 Views
  • 1 replies
  • 0 Helpful votes

I am trying to configure an ASA5520 using CCO configurtor, But cannot see any options to select Active/Active failover license for softrware. Does the default software supports this configuration ?

Hello!I have VPN site to site with rsa-sig authentication and on one router is also as server to easy vpn solution with pre-share authentication. When the user connect to the server via VPN software client with local authentication thanks to this com...

by Not applicable
  • 449 Views
  • 3 replies
  • 0 Helpful votes

Hi Everybody,I have a branch office with a 2691 with a wic-2am and dial backup configured.When dial backup is issued I receive the message "Chat script dialout finished, status = Connection timed out; remote host not responding".However, when I rever...

mnkojima by Level 1
  • 354 Views
  • 2 replies
  • 0 Helpful votes

if a rip enabled primary interface goes down and is backed up by a dialer 1 Floating static route with an admin distance of e.g 200 can a second Dialer 2 be configured to connect to the same location via a second floating static route e.g admin cost ...

larrys by Level 1
  • 1276 Views
  • 8 replies
  • 0 Helpful votes

The documentation on CCO is a bit confusing over the memory configuration for the 837 ADSL router. It originally shipped with 32MB, this increased somewhere along the way to a default of 48MB. What wasn't explained was whether the 48MB was board an...

Hi there- anyone have a sample config for Nat traversal on a PIX (501) running 6.3?Sadly, I only have a single public IP, used by my router, and the ISP doesn't support PPPoE. So, my layout looks like this:(ISP)---(Router)--(PIX)--LANAs a result, I'm...

0r8it by Level 1
  • 720 Views
  • 3 replies
  • 0 Helpful votes