Just started recently.Anyconnect is ALWAYS starting up with blank "Connect to" field.It used to remember the URL but not any more.I am running Linux Ubuntu 22.AnyConnect version: 5.1.8.105I have found the xml file at "~/.vpn/.anyconnect" which does h...
Forum Posts
Hello, A customer have more then 80 L2L VPN tunnels from their HQ to smaller remote offices. Primary the connections to those remote offices are via MPLS and the VPN tunnels are for backup purposes. When looking in FMC, I can see that most of the tun...
Resolved! Cisco Firepower FDM
NAT Exempt configuration for Sit to Site VPN traffic on our Cisco Firepower device managed via FDM. Currently, FDM does not allow ASA-style NAT commands (such as nat (...)) in the CLI or through FlexConfig. These commands are blocked because FDM uses...
Hello, A customer have some asymetric routing issues after a power outage on their local site. They are using MPLS as primary connection to their DC and a static L2L VPN connection as backup. There is a /18 network beeing anounced over MPLS from the ...
Hoping to get some help or guidance on next step. I have a C1111-4p configured as a spoke that is on a LAN (i.e. NAT). The router is configured with a static IP on it's "outside" interface. Beyond this I have no control or insight. What I do know is ...
I have a computer that will need to be connected to another device using an ethernet connection and my network (ethernet preferred but will be fine connecting with Wi-Fi. The computer will recognize all connections simultaneously within "Network Conn...
Resolved! FTD Dynamic L2L VPNs
Hello, We want to have a FTD (with static public IP) and several Cisco routers (with dynamic IP) connected with IPSEC IKEv2 L2L VPNs with different PSKs for each VPN. We dont find on the FTD how to check the receiving ID that the router would send t...
Hi,I have a VPN setup between two cisco IOS routers running IKEv2It works fine with no issuesI see the logs below and Im not sure I understand what they are.I see IKEV@-5-SA_DOWN every time the IKEv2 SA lifetime is up and renews. I also changed the l...
Hello,I have been receiving continual pop ups for several weeks from Cisco Secure Client on my corporate Macbook saying "The VPN client agent was unable to create the interprocess communication depot." This pop up interrupts whatever I will be workin...
Hello, we're running Cisco Anyconnect 4.2 NAC to connect to our VPN. I'm running into an issue where it's telling me that there are no network adapters. I've tried uninstalling/re-installing the network adapter drivers, Cisco NAC and I just can't get...
Hope this helps someone. I went through a newly developed issue regarding Site to site tunnels. I had to make a new site to site tunnel between two sites. I routed all DNS through the tunnel to a DNS server on the other side until I could create a DN...
Hello,I am experiencing a problem when using Cisco AnyConnect VPN to connect to my university network. When the VPN is active:WinSCP freezes or disconnects immediately when trying to access my HPC cluster (Stromboli).University websites such as Moodl...
Hello, I'm planning to configure a new L2L tunnel between to FTD firewalls, where one side is getting a dynamic IP from the ISP and the other side have a fixed IP address. I found some older guides recommended using Hub and Spoke as VPN topology, but...
Hello all, Having an issue that comes up every once in awhile with my AnyConnect Client where I cannot click inside the drop down box and type in a VPN to connect to and then sometimes I can. It seems to come and go without me doing anything (that I ...
Resolved! Cisco Firepower 1010 Vpn configuration
Hi Community,¿It is possible to configure a client VPN using IPsec without License or use the SSL certificate and key?I only found this link: https://www.cisco.com/c/en/us/support/docs/security/anyconnect-secure-mobility-client/215532-configure-remot...
