Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Setting a Port Number for WLC Syslog
Hi Guys,Is it possible to set up a port number for syslog on WLC 5520? On the switch we can set it up by issuing the command logging "host 192.168.100.100 transport udp port 5678", but so far I did not find it for WLC.
My Cisco AP 2802i Not Joining with WLC-2500. it is the only ap i want to connect to WLC.[*12/05/2019 17:30:38.3775] SYS-COND: AP is in fair condition[*12/05/2019 17:30:38.8789] DOT11_CFG[0] Radio Mode is changed from Local to Local[*12/05/2019 17:30:...
I am wanting to enable rogue detection on my 5520 WLC's for the purposes of detecting rogue AP's connected to the wired network. Is RLDP required to get an alert from the WLC/Cisco Prime? Has anyone had any experience with enabling RLDP, and are th...
We have an existing concert hall that was never planned for WiFi coverage. We will have to do runs for the lower level. A picture is below. The upper level can hold 570 people. The facility is about 100x100 feet with the inner portion of 68x75' be...
We have probably 15 subnets each with a unique ME setup running on them with groups of APs in each ME. Each acts as a unique ME. ( I know only one ME is allowed per subnet.) I preconfigured a bunch of APs (3802Is) on one subnet so they would have the...
I have configured ISE for wireless 802.1x authentication for a client. The WLC is a 5508 running version 8.3.150. ISE is version 2.4 Patch 8. We had been testing Windows 10 and 7 laptops with the windows native supplicant. We performed successful...
i am using Aironet 4800 with Huawei PoE+ switch , 5Ghz Radio disabled because not enough PoE power. switch providing 30w and device requested 13.4 only. Mobility express configured to use both 2.4Ghz and 5Ghz radio. [*12/08/2019 08:41:17.9610] Radi...
I have a AIR-CT8540-K9 running version 8.2.167.6 which doesn't have 802.1AX. The recommend version is 8.5.151.0 Can anyone tell me if this has 802.1AX? I know 8540 Wireless Controller does have 802.1AX but I can't find out when it was added.
Resolved! WLC 5508 - Redundancy
Hi all! Today I have one 5508 WLC in my system.I want to ad another 5508 to the system, for redundancy reasons.As far as I understand, I need the HA version. Is it possible to buy a normal 5508 with 12 AP licenses, and make that work?Or do I need to ...
Hello,I'm experimenting a strage issue with some AP1142 that prefer getting new IP from DHCP server rather than using the static ip already configured.I've got more than a hundred of 1142 APs already conected to a 5508, all with s...
Resolved! Cisco 2500 Series Wireless Controllers
we have Cisco 2500 Series Wireless Controllers and Cisco AP (AIR-CAP1702I-D-K9) in our company and need to extend the WiFi range of device, don't want to change the device.please suggest any cost effective solution.
I have a WLC 3504 at a central location and six sites that use it, including the site containing the controller. The controller has an Internet breakout on port 2 and LAN access on port 1. I am looking at implementing Flexconnect and have been throug...
Hi! I'm at a complete loss here.My Meraki MR33 is working fine when I connected it Directly to our Modem-Router but now when I connected it to our firewall the Led indicator is steady orange. How to tackle?
I am trying to set up a very basic network on a WLC 3504. I want it to use web auth with a SSLcertificate signed by a 3rd party CA. The cable plugs in to port 2 on the WLC and goes out to the Internet using a dedicated port on the CPE on VLAN 11. Thi...
Facing this issue, few APs were not working so rebooted the WLC, after reboot no APs were showing, set the Controller to factory defaults, configured as per the cisco guide but no hopepresent situation:WLC 4404, APs:LAP1242AG-E-k9Acess Points are on ...
