I'm having this issue currently with an MR32 model.802.11 association rejected for load balancingIt happens where a user cannot connect when there are too many people in the room near the AP, but once everyone leaves, the wireless works for them. Thi...
Hello at all, I have a customer who wants to know the state of the vWLC VM to switch to an 2nd host in case of error.I did not find anything about the Hyper V integration services for vWLC.Are there no integrations service for the vWLC?If not, how el...
Hi,I'm trying to extract AP details like model, MAC, serial number, IP address etc., of all the AP that is available in our prime infrastructure but I couldn't extract. Please let me know how to get those data. Thanks,Ramkumar
When turning on my WAP AIR-CAP1532E-Z-K9, I get the below messages from the WAP and it won't join the WLC, it just cycles around with the same messaging as below.Nov 13 06:23:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.16...
Hello,I have some 1042N ap that i used to controled with the WLC, and i would like to use it without the controler, as a Wifi router or autonomous Wifi Access point (ssid repeater).Can someone tell me how to do? a procedure, firmware....? any tips.Tx...
Mates,I am planning to Buy MR-84 access point 11 quantity, with Dipole Antenna( 4/7 dbi ) ,Could you please let me know, is this correct part no MA-ANT-20 and how many quantity need to order?Regards
Hello Seniors,I am having a slight challenge deploying AP's 2800 series work in a vlan environment. I have a cisco mobility express AP-2800 deployed as the controller while other 4-AP's are running CAPWAP image with all connected to the cisco mobilit...
Hello, I am a complete beginner. I'm struggling a lot trying to access to the WLC 2504 using the GUI. I can configure the controller using the console port, but I cannot access it though the GUI. I set the Management IP address as 192.168.50.10 but ...
Im trying to schedule a wlan to disable and enable it again after a specific a period of time. I get an snmp error MIB access failed. SNMP Community may not have write permission, check and try again. : xxxxxxx:x.x.x.x as image attachent shows. I can...
Hi, I just discover bluetooth advertising, which is probably great for our business.The idea is that we are creating campaigns and push it through notification of user's phone that has an enabled BluetoothWe tried splashaccess but it needed an Applic...
HiCan anyone tell me if there is any guide out there that tells me how to interpret the reports that can be generated in Cisco Prime. For example if I run a report on client count per AP, is the result telling me how many different clients connected...
I have a client that has two wlc 2504. The configuration was made to be in HA SKU N + 1. At the moment of connecting both in the network it is observed that the mobility group looks good and both wlc are seen. But at the time of restarting the primar...
HELLO I HAVE THE PROBLEM WITH DISCONECTION CLIENT DHCP can someone help me with this issue.
Dear Community, For Smart Lic activation Internet are needed. What if management interface vlan can't access internet for the company policy reasons?Cisco 3850 has capability to select which vlan to use to get an access to the internet. Any chance to...
Hi we are blocking RDP from wireless for all wireless clients how I can enable it for specific client to specific network Thank you
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |
