Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello all,I have a C9105axi-b, which I know after reading around can be converted as a EWC ap, I followed a couple of youtube videos, I also did the day 0 setup, but somehow for the life of me, I can't reach or ping the INT0 of the AP, I'm coming fro...
What kind of material is your accesspoint Cisco Catalyst 9136I and what disinfectant can be used in clean rooms / GMP zones for disinfection without any impact on the material?
Hi all,I have a 2800 AP running Mobility Express with 3 x 2700 APs.I have a device connected to my single WLAN using 2.4Ghz and I need to access it from devices connected to the WLAN using 5Ghz.In the WLAN settings, the 'Peer to Peer Block' option is...
Learning objective Identify how Multi-Link Operation (MLO) and dual uplinks increase throughput, reduce latency, and improve reliability for Wi-Fi 7 connections. Learn Cisco's Wi-Fi 7 achieves zero-friction wireless connectivity through Multi-Link Op...
I have an internet gateway, with its own WiFi, running a DHCP server. I connected my MR57 to one of the ethernet ports and setup a 6GHz-only SSID in bridge mode. I connect my clients to the SSID and they get a DHCP address from the server on the gate...
I saw in this Cisco deployment guide that it states support for 2.5 Gig Ethernet speed with 802.3at starting from IOS-XE 17.15.3. I am currently using a C9176I with a C9800 running 17.15.3, but I noticed that the speed does not show as 2.5 Gbps. I’m ...
Hi,I'm trying to figure out how to convert Meraki APs (CW91xx) to Cisco mode so they can connect to a WLC 9800.I haven’t been able to find the procedure online. Could you help me with this?Thanks in advance.Mau
Resolved! CW9176 Power Issues
We have a mixture of CW9164 and CW9176 APs on a newly-built site. All (Cisco) switches are configured to be able to supply PoE+, and all switches are dual-PSU, so have adequate power. I noticed a number of CW9176 APs that have correct port configurat...
topologyWLC statusinterface configurationWLANsThis is my fictional network topology which has nothing to do with reality and is only for educational purposes and is not referred as classified.The problem is with L2 which is succesfully connected to L...
Hi everyone,At our factory, we’re experiencing a strange issue with one device and our Wi-Fi network. We're using a Cisco WLC 9800 controller with C9120AXI-E and AIR-AP2802I-E-K9 access points. We have two SSIDs: “secure” and “guest.”The problem is w...
Hi everyone,In a Cisco environment, we are experiencing chronic network drop issues. We are using the C9800 controller (software version 17.09.03) and APs of the model C9120AXI-Z (software version 17.9.3.203). We are utilizing a 5GHz CA network, and ...
I have two separate departments of the same organisation on adjacent floors using the same SSID.Depending on physical location the SSID of the adjacent floor is picked up, which incidentally uses a different IP range. I can not change the SSID name a...
I am looking for helping figuring out what kind of mount I should get for my MR46 ahead of installation.We are in the middle of construction and looking at some kind of arm mount so it is not directly mounted against the metal wall.Has anyone tried m...
Hello team.We need your advise for above WI-FI project. Our customer wants to use Meraki AP for their environment. You can find the floor plan below. Also, there will be max concurrent 200 user that connected the WIFI. Most of the users are software ...
We have a warehouse that we recently deployed 5 MR44 AP's. Upon deployment, we forgot to identify the AP, and therefore the Dashboard is not accurate in reference to the name of the AP and the actual s/n or mac address.The Meraki AP are very high so ...
