Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! 9166 Not Leaveing CAPWAP Discovery
Hi cisco community,We have recently deployed a 9800 WLC and are attempting to join several 9166. I have confiqured DHCP 43, and DNS A record which appear to be working. Routing between WLC and AP is functional and DNS entry is resolving correctly. I ...
Resolved! LocalAuth and 6E
I have a number of sites which are remote from the core network, for which I have deployed Local Auth. However, I want to upgrade the sites to 6E, which at present does not play nicely (in the Meraki world, anyway) with Local Auth.I guess enabling 6E...
Hi,When the access point reboots, it suddenly goes into the init>> state. I tried finding a solution to resolve this issue, but I couldn't sort it out. Are there any other ways to address these kinds of problems?Please choose one of the following boa...
Splashページでユーザがアカウントを申請後、アクティベーションせずとも10分間のインターネットアクセスが出来てしまいます。アクティベーション前のインターネットアクセスを制限する、もしくはアクセス出来る期間を10分以外に設定することは可能でしょうか。ご存知の方がいらっしゃいましたらご教示いただけますと幸いです。
I'm using wlan as hidden for WLC5520. I'm simply using it as a psk,It is said that the terminal ends the session unspecified and asks for psk again. session timeout or idle timeout is unchecked. The device is intel ax211. Is this a hidden problem?Is ...
HiI am going to put a MR36 as WiFi AP in a remote site with Bell ISP (no Meraki MX in the site). Would it work for same SSIDs in our Wireless system and will show the Meraki dashboard?Thank you
As per the subject really, we would like to trial Cisco ISE for AD authenticated wifi, but can quite work out the licensing model.So just really trying to find out what level is required for just AD authenticated wifi.
I have an MR36 that pulled a bad ip because the port was configured with the wrong vlan. I removed the unit from the dashboard, reconfigure the port. The unit is pulling the right address now but when it get imported into the dashboard it shows the w...
Hello Guys, We have Foreign and anchor setup where there is one SSID with PSK. Foreign WLC is passing PSK authentication but eventually receives client deletion due to below error. Controller initiated client deletion with code: CO_CLIENT_DELETE_REAS...
Resolved! 10.128.128.128
I had some fun today when we had an SSID that could not access multiple resources. It turned out that when we created it, we had forgotten to allow traffic to the LAN. If you see trace routes failing on the first hop at 10.128.128.128 then this is th...
Hello,Can someone please help me with the following?What's the difference between a local mode AP and a FlexConnect AP that does central switching?Both of them have CAPWAP data and control tunnels to the WLC, and neither of them work if the connectio...
Hello Cisco WLAN experts,when I do an radioactive Trace on our 9800-HA-WLC, I have noticed that it takes a very long time to finally present the result in Gui.In this example I took a Radioactice Trace inclusive Conditional Debug to search back packe...
Dear Meraki Support Team, I am currently using three Meraki access points in our deployment: two MR53 units and one MR56. As Vietnam has officially approved the use of the 6GHz band for WiFi 6E, I would like to enable this functionality. However, I h...
I have a one Access point that is restarting Daily.
Hello Team,I'm encountering an issue where a tablet device with a statically assigned IP address reaches the RUN state on the Wireless LAN Controller (WLC), but its MAC address does not appear on the switch port connected to the AP it's associated wi...
