Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi all,   Please i need signification of WLAN Profile Name and if we can have the same SSID in different profile name, and what can profile name change in our architecture    Thanks

RosVerde by • Visitor
  • 1066 Views
  • 2 replies
  • 0 Helpful votes

Dear Community,   I would like to implement a 2 stage web authentication on a WLC. The Current Authentication is pass-through which i would like to keep and have it time out after like 20 minutes and redirect the user to to a web survey page, after t...

pmehanna by • Visitor
  • 770 Views
  • 1 replies
  • 0 Helpful votes

Hi i have WLC with 15 Active AP , i have big problem , for example i have 2 AP nearly me , 1st one far me about 2 meter and another one far about 7 meter , the problem is my device connected with 7 meter AP !! and didn't connect with the near one!!  ...

Murad* by • Level 5
  • 2200 Views
  • 9 replies
  • 0 Helpful votes

Tengo dos WLC controller versión   WLC 5520 con versión 8.2.161.0 WLC 2504 con versión 8.2.166.0   Requiero actualizar estas dos WLC a la versión inicialmente 8.2.170.0  , pero no encuentro que vulnerabilidades que parcha esta versión . si puedan ayu...

anderson by • Frequent Visitor
  • 2062 Views
  • 2 replies
  • 0 Helpful votes

Hi, We are implementing a new wireless network using Cisco. Our design is using FlexConnect and multiple SSID. Each SSID is associated to a VLAN: SSID1 - VLAN 100 SSID2 - VLAN 200 SSID7 - VLAN 700 etc. The interface for the AP's is a trunk: interface...

Ronni Feldt by • Community Member
  • 12885 Views
  • 8 replies
  • 0 Helpful votes

We've got several hundred APs running in Flexconnect mode and locally switching our WLANs, until recently they were all 2700 or older APs. Now we've deployed some 2802I APs and we've got an issue with clients connecting to these. I've configured them...

M. Wisely by • Level 9
  • 5850 Views
  • 10 replies
  • 0 Helpful votes

what is the approach to troubleshoot disconnection of a user's laptop? Wifi infrastructure is built on access points 2702I with WLC5508 (firmware 8.3), laptop is using only 5 Ghz (connected via "802.11ac") connection (2.4 Ghz is disabled on access po...

wifi.png
Andrey128 by • Level 5
  • 2061 Views
  • 8 replies
  • 0 Helpful votes

Hi All,   After deploying ISE , I'm encountering some problem with the few desktop users as the authentication is very slow (1-3 hours) when they connect LAN cable to their desktop.    Is this the probelm with ISE? How can i troubleshoot this? Someti...

Rickey369 by • Level 2
  • 4044 Views
  • 16 replies
  • 0 Helpful votes

hi i have Cisco Virtual Wireless Controller that are supported 3000 Access Points , and because this is my first try to work wit ( virtual ) device my query here , is this VM worked normally with AP1142n or not ? and if there any tips can help me to ...

Murad* by • Level 5
  • 4326 Views
  • 17 replies
  • 0 Helpful votes

Can anyone tell me why these AP's go into error disable and the only way to get them working is to run a no spanning-tree portfast bpduguard on the switch. Then reboot the switch and it all come up fine.

Review Cisco Networking for a $25 gift card