Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I am setting up a 5520 WLC for the first time, I have set the local credentials and can access this appliance via console. However my credentials aren't working via SSH or WebGui? Logs seem to show AAA-3-ACCTREQ_SEND_FAILED I also cannot synch wit...
I have added my MESH AP's to the map and the MESH links appear on the map as 0 SNR. I can run the link test Parent-> Child and vise-versa and SNR os good. If I go to Monitor->Access Points-><AP Name>-> Link detail, everything is zeroed out. I do h...
Hi All, I am not sure this is the appropriate place to report a bug, but I haven't found any better forum. I use Cisco AnyConnect Secure Mobility Client 4.4.02039 along with its Network Access Manager module. I use Windows 7 64 bit's in-built PPP...
Hi TeamHope you doing well..I need to deploy new 3 x AIR-CAP3702I AP as a standalone AP,i ordered AP with default image (SWAP3700-RCOVRY-K9) and now need to convert it to Autonomous Mode.Please suggest the steps for 3702I conversion.Thanks in Advance...
Hello All I have 3 APs with autonomous software, so i want to connect them as P2MPT via wireless not wired, One as root-bridge and the other non-root-bridge, the non-root-bridge APs connect to switches to brovide their clients with internet connectio...
Hello, I am using Cisco Prime 3.1. I need to set a threshold for AP Utilization. Then, need to generate alarms for when the utilization is above that limit and receive those alarms by e-mail. I've seen that some questions about this issue have been...
Hi, I have an DMZ WLC- 5508 and internal foreign WLC cisco flex 7500 . I configured mobility anchor between these two WLC. I get data path as up and control path to be down. Also between these WLC s firewall is not there. Please help.
HI, We plan to deployment a WLC+LAP,the WLC is 5520,we want to ap get ip address by dhcp,and get wlc's management interface by dhcp option 43.But,AP can get ip address,they cannot join WLC.Is there any error?The dhcp server config as below,and the ...
Hi Team, Cisoc LWAP - 1142N doesn't joining to remote WLC (Flex connect).WLC Model: 5508. Its trying to downloading the image and gets failed. Please advise. Thanks ganesh
Hi All,Would like to know if anyone here has experience our issue.When user below opens her laptop every time she comes to office, she is unable to access the Splash page portal whenever it connects to any of the active SSIDs (Ex SSID1 SSID2) and to ...
Is there any way to disable the WLAN-controller in the Catalyst 3650 so they not show up as WLAN-controller in Cisco Prime? We have no plan to use the 3650 as WLAN-controllers and do not want them as WLAN-controller (with a 0 AP-license) in Cisco Pri...
Hi, My company provided me an AIR-OEAP602I-E-K9 office extend, when I connect it to a ADSL router (friend of mine), ALL is good, I see my company Wireless network at home and I can connect. When I plug it on my TP-LINK MR200 4G LTE route...
Hello, I'm using 8.5.131 and I can't figure out how to block clients from joining a WLAN for specific time and day. I created an ACL that denies everything inbound and outbound. Then I create a local policy and just set the ACl, the time and days and...
Hi In some Access Switches the APS are getting Power Deny after Rebooting the Switches the APs are registered The following output of one Access Switch as shown below i1/0/32 auto off 0.0 n/a n/a 30.0 Gi1/0/33 auto on 24.5 AIR-AP1810W-E-K9 4 30....
Resolved! Access Point 2702 Keeps booting
Hi! I recently update the default gateway of my wireless infrastructure, when one of my access point reboot, it stopped works so I tried somethings to restart the AP but nothing worked so I decided to do a factory reset at the end of the reboot the...
