Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Cisco AIR-AP3802 Mobility Express
Hello, I need to download Mobility Express for my just purchased Cisco AIR-AP3802. This is so I can set up the access point in "standalone" mode. I purchased the access point through Server Supply, and was of the understanding that I should be able...
After getting a Cisco device set up, my habit is to back it up in case something bad happens. I am unable to do this with the standard method on the new 1815i I set up yesterday. The upload-sw command is missing from archive. Is there an alternate ...
Hi, I just got a couple of AIR-AP2802E. How can I check if it's running Lightweight Image or Autonomous? Show version command doesn't show k9w7 or k9w8.
Hi! We have a wireless controller (Cisco 5508) and some LAPs in a bridge mode (mesh). Is there a way to block certain clients from joining certain APs? To elaborate let's say there is MAP1 and MAP2 that are near to each other. We want this certai...
I would implement IPv6 in my network equipement(3560, 2811 ,etc.)but i don't find the good IOS for an Aeronet 1242AGFor further details, it seems there is no "Advenced ip services" IOS for Wirless equipement.Also i have try to activate IPv6 in my cla...
So we have 2 WLC's. We have multiple buildings. We have the same SSID: Corp. Each building has its own VLAN or WLAN assigned to Corp. If a client connects to building 10 and gets 10.10.10.5 IP and then goes to building 20. This happens with mobile de...
Will Cisco Mobility Express AP support PEAP−MS−CHAP v2 Authentication? I know this protocol is support Cisco 2504 or 5500 Controller; but is this protocol supported by Cisco Mobility Express AP (1832 or 2802)?
I want to set up my WLC to authenticate the management-users using LDAP instead of having local management users. How do I configure that?
Resolved! %CAPWAP-3-DISC_UNSUPPORTED_AP error
What is the supported image version for C3850-12S to connect AIR-AP2802E-E-K9 . I could find the supported version going through the compatibility matrix document https://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matri...
Resolved! Repeater mode alert?
Is there a way that I can get an alert if an MR goes into repeater mode?
Resolved! Avoid bridge connectivity
Hello, I' like to know how can I avoid a bridge connectivity between 2 APs?? I have a couple of MR33 already working on a network at the same VLAN and I will install a new AP assigned to a different VLAN, but when it startup it get connected as bridg...
After updating to Prime Infrastructure 3.1 (or maybe already to 3.0), when I chose Monitor/Access Point Radios it lists over 27000 entries, when it should be around 2000. Some radios are duplicated 20 times. I have searched the bug list, but cant fin...
I have WLC 5508 with 12aps license, i will buy a new license with 50 Aps, my question, its possible add new license with 50 aps, totaling 62 aps licenses?
Hi Community. There are some papers which show the difference, but these aren't very clear.As i know Clean Air 3.0 will automatically adjust power level, etc. and Clean Air Express doesn't. Is that right, or what should be the main fifference? The CA...
Hi Guys, I have not much experience and knowledge on wireless and current facing interference issue... The photo shown channel utilization 82% and interference 75% high , even i change the channel for some of the AP but its still the same. is t...
