I have few APs joined the C9800 WLC. The WLC is running on firmware version 17.9.3. Regulatory domain is set as MX for Mexico. But the operational status does not come up.
Forum Posts
Resolved! converting C9130AXI into EWC
I am currently trying to convert a C9130AXI into EWC I have done a factory reset using 30 sec push of factory reset button see belowWait for the button to be released ....Button pressed for 36 secondsSetting env for full reset..Writing to Nand... do...
In short, I'm looking to setup 'deploy and destroy' within a lab environment, and I'm currently using an instance of The Foreman to achieve this, having configured the lab's vSphere instance as a Compute Resource within Foreman. I'm currently able to...
Hi community, I have a pair of WLC 9800 in HA mode. The management interface labelled SP on the standby WLC is down, lights out even though it is configured the same as the SP port on the primary (different IP). Is this normal behaviour?
I am using 9800 wireless controller with C9120AXI wireless AP. When I connect to wireless SSID from a device via EAP-TLS, EAP-PEAP, it will connect successfully with TLS 1.2 protocol. When I connect to wireless SSID from a device via EAP-FAST, it alw...
Hi allI have an issue where when some users are roaming from 1 side of the building to the next they drop off the network and have to forget and reauthenticate. I didn't set this controller up but I can see Fast transition is adaptive enabled. So I s...
I am deploying the Cisco 9136 AP for 6E in our new office building at high density. What has been the recommended power on this AP in office settings? I typically deploy from 8dBm to 14dBm but curious what others have done with this new AP over 6Ghz
Due to the license issue in the c9800-cl model, the number of joined apps was limited, so we created a rum file with air gap and imported the ACK.rum file by referring to the link below. https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-98...
Hi We are going to purchase Access points C9115AXI-I and C9115AXI-EWC-I . Both are same prices But C9115AXI-EWC-I is announced by Cisco to be end of sale end of this month. So we can purchase only C9115AXI-I with the DNA essential license I need to c...
If connectivity between WLC and AP goes down for sometime, will clients connected to AP's face network disruption? or there is any grace period that client's rest of use(browsing, access) will work.
I have to deploy APs to branches using flexconnect. Do i need to preconfigure the APs on my local controller then ship them out or can i just load in the MAC along with the tags i want on the AP ship it out and then itll grab everything it needs? eve...
Hello, We have a problem with a C9800 Wireless Controller (version 17.9.4a) and Cisco C9120 Access Points. Some clients are roaming from one AP to another, while there're not moving from their desk. For exemple, as shown in the exemple, a client in...
Hi. We have 3 new 2802I that we can't get to work. We're using a 3750 switch to power the other 2702 which works fine with our 2500series controller (version 8.3.112.0). Since the 3750 can't provide enough power for the 2802 we bought a couple of D-...
Hello everyone. I have a conference room and it is equipped with a C9130AXI-S. I have searched for the installation instructions so that it can broadcast wifi in my conference room but I can't find it. So I hope everyone can help me with the installa...
Hello Team, I have an issue with BYOD authentication as user is able to connect with SSID and receive IP address but webpage redirection is not happening and Logs shows L3 authentication failure. WLC: C9800 Authentication server: Clearpass. Attaching...
