Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dear Team, We are trying to integrate Active Directory with WLC 2504 controller but not successful. Which is the best way to do? does 2504 will support AD integration or not? I have gone through Cisco Docs but i am finding confusion on AD part. Can ...
Hi, Please help to interpret the "Interference (RSSI) by channel " graph Thanks
Resolved! Single SSID with multiple Vlans
It's known that SSID supports only one vlan but is there any way to make a single SSID have multiple Vlans?
Hello everybody, This is kind a very old subject but I´d like to discuss here some details surrounding CCO that may be not that clear to everybody, at least for me is not.We all know that to users to have a good experience using their device, the net...
Dears, I need your help in find the root cause for the following behavior. I am trying to configure a cellular interface on cisco C881G-4G-GA-K9 router as 3G. But the interface not operational. its showing up/up (spoofing) and not getting IP addre...
Hi All, is there chance to Monitor the NMSP Connection Status between WLC and MSE? The Customer asks for a SNMP Poll / GET on WLC or MSE to see if the NMSP works correctly. In PI we only see that it works or not, but there is no Warning or Event. RE...
Hi, we have a large wireless network consisting of 400 CAP3502i access points integrated with WLC5508, however on remote site they purchase small business access points WAP4410n, I would like to integrate these WAP4410n access points to WLC5508, as ...
Hi, I have AIR-CAP2602 more than 20 units. On all of their APs, CAPWAP Client and WAPI Process are the top process which make 80% Memory Utilization on each APs. Any body know what is CAPWAP Client and WAPI Process ? Thank You.
I am trying to understand what causes the WLC to generate this trap: " Interface:1(802.11a) Operation State Down: Base Radio:() Cause=Dynamic Frequency Selection reset due to no channels available. Status:NA ". From what I can see there are no utilis...
Dear Team, I have these two Access Points "AIR-CAP2702I-C-K9" and "AIR-CAP2602I-C-k9" and I need to convert them to Standalone/Autonomous Mode. Please let me know if it supports conversion from Lightweight to Autonomous Mode? Is there any supporting ...
Resolved! Cisco AP1532E radio problèm
Hi, I have AP CAP-1532E configured with controller 5508 may probèm is : the signal of the radio is very poor . when i put PC near the AP the signal is very good but just i go away from the ap (about 3 meter ) the signal will be very poor; for inform...
Hi In the controller wlc 5760 the cisco Ap 2702 is not registered while 2602 is registered the controller output of of show ap summary as show below Controller#sh ap suController#sh ap summary Number of APs: 1 Global AP User Name: Not configuredGlob...
As described in the article below "When Stateful Switch Over is enabled, there is no SNMP/GUI access on the service port for both the WLCs in the HA setup." So my question is how do you monitor the health of your backup unit in the HA cluster? How...
Hello team, I would like to know if you can help me with the following: First issue: I have a stacking switch 3850 working as Mobility Controller. The IOS XE version is 03.06.03E. Servers are on VLAN 10 and wireless endpoints are on VLAN 51. Ther...
My hardware...Cisco 1300 12.3Cisco Command Referance states......#dot dot11 antenna-alignmentUse the dot11 antenna-alignment privileged EXEC command to activate the antenna-alignment tool for an radio interface. Use this tool to test and align the ac...
