Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello all. Does each Meraki AP require a unique routable IP address? So if you have 4000 APs, you'd require 4,000 unique routable addresses? Secondly, can you configure a private ip on the Meraki AP uplink interface, then static NAT it to a public IP...
Dear All, I have a requirement from client, wherein they would want to have the "usernames" of end hosts that are connected on wifi be reflected in Monitor-> Clients dashboard. The only way this is possible IMO is for the client that are associat...
Hi Guys, Please advise if AIR-AP1832I-E-K9 support Data Roaming, I cant seem to find the information on its data sheet. Regards Tony
Hi, Have simple setup where the wlc uses ISE for Radius for AAA , and get this message %APF-3-CLIENT_NO_ACCESS: Authentication failed for client: 74:8d:08:6a:f1:43. ACL override mismatch from AAA server The authC policy checks wireless MAB and def...
Hi,Do the Cisco Aironet 1540 Series Access Point currently support point-to-point and point-to-multipoint for bridging between LANs in buildings?
Hi When trying to add AP to controller I'm reviewing the following log as the AP is not able to join the controller Below is the results I get with the newer WAPS *Mar 1 00:00:13.011: APAVC: Initial WLAN Buffers Given to System is 2500 *Mar 1 00:...
First off not sure what community to post in. Couldn't find a Meraki specific one. I am going to be rolling out over 100 new sites and we are going to go with Merkai. Each site will contain a single MX, two MSs, and two MRs (5 devices total per locat...
Hello, Data rates enabled can be changed at 2 different locations in WLC, I didn't find information if any priority : RF profiles vs 802.11b/g/n global parameters. - All 802.11b data rates (actually all behind 12 Mbps) have been disabled in global pa...
I am trying to install the vWLC in VMware. However, I get the following error information. Starting portmap daemon....starting usc cd installation scriptifconfig: SIOCGIFFLAGS: No such deviceifconfig: SIOCGIFFLAGS: No such devicelooking for cdrom dev...
Hi Everyone ! I have an issue with Cisco 1832i AP. I already set the SSID for my AP. PCs and Mobile Phones also connected to my AP and could access the internet. But, when I tried to access the AP's IP address for manage some config, I can't login to...
Dear Support team. I am using Cisco Aironet 1200 series. Now I hava a new device want to addition into Cisco system. But I can not do because there is a different point. For detail, let see the picture is attacked and explain me how to change them.
Hello, I run large auditoriums and I am trying to clear the 2.4ghz spectrum for audience response systems that run on Bluetooth. For the WIFI, we run everything at 5ghz and only a few AP's with 2.4ghz since most clients nowadays support 5 gig. The a...
Dear All, we have an odd wifi issue with cisco WiSM2 WLCs running 8.2.151.0 and mainly our 2802I Cisco Access Points. Some connected wlan clients connected to these 2802I APs stop getting arp replies from their default gateway after a while and as a ...
We had a 2504 WLC die (alarm stays lit, will not boot from either image on the box), that has two AIR-CAP2602 LAPs connected. No mobility group was set up. How can we get the LAPs to temporarily connect to another 2504 WLC across the WAN while we g...
Hello all! I have a WLC 5508 with aps 2702, i bought new aps 2802 for a diferente site. On my site i have diferent subnets but the same SSID, how could i coinfigure this new aps with to be associate on my controller with diferente subnets in the same...
