Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hey Guys, I am pretty much new with Cisco WLCs and I just have a question regarding licensing. We are not doing SSO as we have a split data-center design. Our primary is in one state and the secondary is in another. So definitely, we are using N+1 ...
I probably posted in the wrong forum so ill try here! I am having a problem whereby after configuring the WLC via gui, it was recommended i set a static Ip on my router which i have done. I set the subnet at 255.255.255.0, however, on the router it...
Is there a Design Guide out for the IW3700? I need to know outdoor distances vs. throughput. I don't even see it in the Outdoor calculator yet.Thanks in advance,Nir
Resolved! Meraki AP Port Type
Hello, I've a project to implement Meraki APs in an enterprise but I am new to Meraki. Their documentation mentioned the following " Because a Meraki AP can be sending/receiving tagged data traffic as well as untagged management traffic, all Meraki ...
hi, i started big report in mse 10.2. this report load memory and mse is not responding. can i delete report from cli? thank you
we have a local sports complex that had 4 existing 1320 ap,s mounted on field lighting poles. with pelco ip cameras connected to three of the ap,s.they are configured with one root bridge and 3 non root bridges, all in autonomous mode. we recently ad...
I know the 8510 is suppose to support 6000 APs and 65,000 clients. Does anyone know if Cisco has released any information based on throughput. The reason I ask is because with 4300 APs and 32,000 clients we are seeing an average of over 150ms ping ...
I have a client who has been using Meraki MR18 and MR34 Access point with Cisco Meraki controller for guest traffic . 1) I want to know if MR 18 and MR 34 are compatible with Cisco WLC 5508 . 2) Can a AP have two controller . Need here is to have 1 ...
Hi, i configured custom page on mse 10.2 as http://www.cisco.com/c/en/us/td/docs/wireless/mse/10-2/cmx_config/b_cg_cmx102/b_cg_cmx102_chapter_0100.html visitor login is redirected to portal, but custom portal content is not depicted, device screen ...
Hi all, I am in the process of setting up a 2504 with ap's.. With regards to connection, would it be ok to just plug the controller direct into the (Lynksys unmanaged) switch and then the controller would get its IP address from the Ubiquiti router...
Where to find following technologies for Cisco wireless access points? ssid, os version, wids, bonjur gateway, device fingerprnting, meshing, hotspot, mountimg
Hi All, I have 4 units of AIR-CAP2602I-A-K9 cisco aironet. I need to configure this AP to Radius server configurations. 1. All 4 units same SSID. 2. This 4 units of will be deploy to different locations. 3. This 4 units only one vlan 4. Radius se...
Hi Is there a relation between rogue access point detection and clean air , Rogue access point detection is based on the clean air technology ?
Hi Team, I just added an AP to my WLC through "Capwap ap controller ip XX" by using Default Username and Password..."Cisco and Cisco". 1. But is it possible to access my LAP through Telnet / SSH/Https after adding it to WLC. and how? 2. I am unabl...
This thread was opened two years ago but it received no replies so hoping someone can help! I have setup a new Guest Wlan on our vWLC ( AIR-CTVM-K9 ). Its a in a separate subnet and VLAN and I have DHCP proxy enabled. IP helper-address added to the ...
