Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, I have run some tests on our outdoor mesh network. I got acceptable SNR (25-35) but packet error rate was kinda high(10%-35%). I found one 802.11FH interferers. Is this single interferer causing problems ? or there could be any other issue?? Than...
Gentlemen, I have a problem with the company that users are connecting and disconnecting the logs and reports about loss of BSS. I read all blogs and forums on this issue and tried all suggestions but continues.logs:Sep 14 20:57:27.391: %DOT11-6-DISA...
hello,I would like some help or documentation where i can find or estimate the recommended number of clients for the Access Point Cisco AIR-CAP3502P-E-K9 to make the network performance acceptable for Voice/Video ?I need this information to estimate ...
Hi ,PC cannot see particular SSID and it see only channel in an area SSID 7 : test Network type : Infrastructure Authentication : WPA-Personal Encryption : TKIP What could be the problems Thank you
HI All, I hoe you can help me I have tried the search functions and I think this is achievable but I would like to confirm with you first hand.We have A cisco 5508 running Code 7.6.130.0 that is used to anchor out guest clients for out guest SSID. W...
Hi All, We've two 8510 WLCs. one Primary 8510 WLC and another 8510-HA unit. The initial design was to use them in HA pair with AP-SSO. Can we use this 8510-HA unit as DMZ anchor controller for dedicated guest network? I know 8510 has RTU licensing, ...
We have the WLC 5760 work with the NPS & AD server for 802.1x authentication enterprise wireless .How can we do to achieve the result of only one device can be connect to wireless per account ?Any setting on WLC to do that ?
We installed that WLC 2504 Firmware 8.1.102.0Find log there picture but I don't know to mean this logso I have a question1. What is this log mean?2. This probem reslove method.Please help me~
Hi, we would like to upgrade ISE (1.2) to 1.4 and I was wondering if there is a minimum WLC version that is required for ISE 1.4? I haven't found anything in the upgrade documentation.. thanks very much!kind regards
Resolved! 2 SSID with same Vlan.
My Cisco 1700 series access points having already 2SSID's and each one is mapped to different Vlans(SSID1 to Vlan10, SSID2 to Vlan20). My requirement is i want to create one more SSID(SSID3) and i want to map in to same Vlan(Vlan 20). Is it possible...
Dear Cisco Support, How to configure the Cisco AIR-SAP1602-CK9 . Using what method or step by step knowledge transfer .I'm a beginner and totally new to Cisco AP. Thank you. Regards,Eric
Okay this is waaay out of topic(Cisco), but Exalt is endorsed by Cisco haha soo going to ask hereIs the website down?exaltcom.comAny exalt users out there? is the website okay on your side?PS: For the interest of others, Exalt is a Wireless P2P and P...
Hi Guys,Please provide the recommended procedure to avoid Wireless radio channel range collision. The scenario is, there is 14Nos of Cisco 1700 series is connected in one hall. some of the area is having internet slow even signal strength is excelle...
I am looking to deploy the Cisco 3702i Controller-Based- Wireless Access Point at my site and control it with a Wireless LAN controller from another site. My questions are: How much bandwidth does this configuration use (talking between the CAP and t...
Hello,We have two WLC and we are planning to add a new one.How i can add the new controller to High Availability configuration of the APs?. We dont want to do it one by one.Thanks
