Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi Team I'm working in a couple of WLC2504 deployment in a N+1 HA SKU topology In both controllers the software version is 7.6 . We stablish the N+1 HA configuration step by step like in this guide:http://www.cisco.com/c/en/us/td/docs/wireless/t...
Hi all,our customer is looking for a Mini-PCIe WLAN cards (802.11a/b/g) with CCX support for his moving Thin-Clients (Enterprise area).Does someone has experience and a recommendation for a good Mini-PCIe card? Many thanks. Regards,Uwe
Hi,i have campus wireless network with Cisco Wireless LAN Controllers 8510 and ISE 1.2, its working fine, i want to setup remote sites and want to place WLC and ISE (PSN) over there and need authentication done locally with ReadOnly Domain Controller...
HiI have new WLC 5508 and 20 AP, but there are Management and service Port, my question is should to be Management IP from management subnet in existing network and service port from Data subnet in existing network? Thank you
Hello, I have a question for cisco Aironet 1500 series. I want to connect two of them as point to point in a distance about 6 km (kilometers). So there are two questions, can them be connected as point to point to transmit signal and the second one w...
Hi Experts, I have two SSID configured with central switching 1) Corp SSID 2) Guest SSID I have question about guest SSID ..since I have requirement of configuring guest with central switching and gateway for guest ssid will be configured in HQ ....
Hi all,for compatiility reasons I was used to enable both protocols on all the access points I prepared for customers of mine, both as regards on lightweight ones that standalone,Now, as you all know, not only it's not best practice, but on the lates...
Resolved! Cisco Bridge APs
Does Cisco still support Bridge APs. Like long range once, I do know that all APs can be set to be a bridge, but with regards to range, it is just a few meters.Also, not interested in Mesh deployments since speed can be a bummer on this kind of deplo...
Hello everyone!I have got Cisco WLC 2504, current version is 7.6.120.0, so I have got an virtual interface on this WLC for mobile users (SSID: MOBILE).I have applyed ACL on this interface "ACL-BLOCK-LAN-IG-MOBILE", so this ACL blocks all traffic to L...
Resolved! Tools for Wireless Networks
Dear what are the best tools for monitoring, vulnerability test, testing WLAN over Voip, etc. for wireless networks either hardware or software? BestRegard
Hey guys,I updated the software to version 8.0.110.0 for the WLC 2504 two days ago, it worked fine until this morning that it crashed, it's was blinking amber and green and the SYS light as well, I couldn't ping it, then I took the power cable off, a...
Resolved! 7.5 web-auth client sleep timer feature
The 7.5 release advertises the ability to configure a timeout value so that guest clients which go to sleep are not re-prompted for web-auth. Does anyone know if 7.5 would only be required on the anchor WLC or must it also be on t...
Is there a way to set an idle timeout value on Autonomous Access Points? I have been researching and I see it is possible to do this on a WLC using Lightweights but the only timeouts I can find regarding Autonomous are Session/Holdoff and Re-authenti...
Hello Guys, I have some AirTight APs, SS-300AT-C-60, which are working standalone as WIPS. Those devices can work as AP too butI was wondering if a Cisco WLC can support it. I mean, is there any way to manage these AirTight devices via CAPWAP using a...
Hi guys, I've managed to 'upgrade' the onboard 802 AP to lightweight in error but cannot find a way to 'downgrade' it back to autonomous mode. I've read various threads but none of then work for me. Any advice would be welcome. Thanks Robbie.
