Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I have got myself into a confusion here. I am trying to figure out an option where I can centrally switch some clients on a flexconnect locally switched WLAN. We cannot go with AAA VLAN override here since VLAN IDs are different at different location...
Hi,Is there a way to schedule automatic configuration uploads (backups) on WLCs? It should be done without using WCS.Thank you in advance.Regards,AndrasThe solution has been added in the following document;-https://supportforums.cisco.com/docs/DOC-21...
Hello, I will need to migrate a wireless deployment of about 300 FlexConnect APs from a 5508 HA pair to a single 5520. I'm running 8.1.131.0 on the 5508 pair, and plan on bringing the 5520 up to the same version. Is it possible to cut and paste certa...
Hi, We are having problem with CMX installation. CMX 10.2/10.2.1 installation script throws the error message when we select new device option,"Bringing up the interface eth0: Device network does not seem to be present, delaying initialization [FAILE...
To whom this may concern, I'm a newbie on here and I'm hoping that someone could please help because I'm also new to Cisco products as well. I do have some experience with Cisco CLI and setting up some of there routers and switches but not so much ex...
I have several access points AIR-CAP2702I. How to evaluate whether switch (which I plan to order) 'WS-C3560X-24P-L' with 24 ports 10/100/1000 PoE+ (with 370W power supply) sill be able to support 'full power' mode for ~10 access points AIR-CAP2702I (...
Hi Is there no way or plan to get Windows Mobile (8.1 and 10) to BYOD-register in ISE 1.4 or later? The same question also for computers with Chrome OS. It works like a charm with iOS, OSX, Windows and Android. Best regards, /Kjell
Hi I'm a design consultant working increasingly on WAP design, can anyone provide some insight on mounting WAP's under or recessed into a suspended metal tile ceiling? In my opinion this acceptable as the metal plane of ceiling is not blocking the di...
Hi I'm trying to "resurect" an old wireless network made with Cisco Aironet 1100. One of the AP has lost its IOS (due to an error while trying to upgrade it through the web interface)I tried to reload it with the "mode button". I can see in my TFTP s...
Hi, I have configure a WLC 2504, i have to pass 2 network between WLC. I have already configure a management interface with untagged Vlan 0, and other is VLAN-40. Here is the information: For Untagged Vlan: VLAN Identifier: 0 IP Address: 192.168.10...
Hi All, Is there a way to only restart the wireless service on a 3850, or does the whole box needs to be reloaded? Thanks!
Hi I have problem to join remote AP 1702 to CISCO 2504 controller. Controller firmware version is 8.0 and local AP,s are working fine but remote APs which is installed at branch office connected with MPLS network, are not joining the controller. APs ...
Dear Team, I have Cisco AIR-CAP16021i-E-K9 AP and I need to configure L2OGRE tunnel manually. currently AP is configured with cisco firmware LWAPP image version 7.4.121.0 and I need the formal procedure of doing this correctly. Further, It is essen...
Hey Cisco,When will the "single WLC only" AirOS requirement for 802.11k be lifted? Also, Can you clarify what the consequences of enabling 802.11k in a multi-controller environment are? Will clients who roam across controllers fall-back to traditiona...
Hi, I have configured HA redundancy on 2 units WLC 8500 series with SSO. After running for more than 6 months, the WLCs have been switchover several time and the switchover reason was "Active Controller Failed". Does anyone know what it means and how...
