Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
The running config is:- Two WLC5508's in HA SSO setup running version 7.5.102.0- about 130 x 2602i APs I need to upgrade to 7.6.130.0 using the pre-download feature to minimize the network downtime.Is it possible to transfer the 7.6 to the controller...
Hi all,I've been getting "%MAC_MOVE-SP-4-NOTIF: Host xx.xx.xx.xx.xx in vlan 123 is flapping between port Gi1/18 and port Po1" entries on my core switches. The topology looks like this:Interface Po1 connects my two 6500 core switches, we have HSRP run...
Hi, I have a query regarding Access Point compatibility, i have been advised to buy the CISCO AIR SAP 26021-EK9 and i am wondering if this will work injunction with my current hardware: CISCO AIR AP114N-EK9CISCO AIR AP113AG-EK9 Kings Regards,Paul
Hi,I just found out that configure terminal is available on a LAP1262N AP-AIR-E-K9 in mode CAP.But another LAP1262N-AIR-E-K9 not the configure terminalFind enclosed AP version and option configurehow have the configure terminal in AP mode CAP, while ...
HiI'll be upgrading a HA pair of 5508's from 7.4.110.0 to 7.6.130.0. The documentation suggests that I just need to upgrade the active and this code is copied to the standby. Then simply reboot. After this verify that the active is not the standby HA...
Can a CISCO Aironet 700w be set up as Antonius Access Point ? I was able to set up 700i OK no problemNeed to Set it up for WIFI site Survey Active to test coverage
Hi,I'm facing an issue in Cisco 5508 WLC.My WLC IOS image version is 7.5.102.0.Problem statement: My WLC is currently in production and catering to a live system. It has to be migrated from existing data center to another. The IP address, subnet mask...
Hi,In the case, when Light weight AP is broadcasting more than one SSID ( with WLC is configured with associated VLAN interface) how does the WLC differentiates DHCP requests those are coming from different SSID before forwarding to DHCP server?Doe...
Hi, I need to backup my current config on my WLC 4400. I want to use TFTP to do so. However the TFTP server for MAC requires that I enter the name of the configuration file in my TFTP server BEFORE I actually download and save the config. But I do...
Good evening,We presently have some minimum data rates setup for our 802.11 deployment (.11b/g disabled below 9Mbps, required at 11Mbps and supported at 12Mbps+ and for .11a/n/ac below 12Mbps disabled, 12Mbps required 12+Mbps supported). Currently ...
Resolved! max power best practice
Hello , could you please validate the following : "we need to set always the max power globally at the WLC to 17 dbm in order to match the max client power to avoid one way communication " ?!!!
I have new 2504 WLC + 1041LAP. I configured the first DHCP scope on WLC and the first WLAN. Then I set WLC DHCP server in WLAN properties and tried to connect to WLAN with wireless clients.My wireless clients are able to authenticate on WLAN, but not...
I've read somewhere that AP's will retain previously joined WLC IP addresses in NVRAM. During reboots, it can use these IP's in addition to the ones learned from the typical WLC learning logic. Wondering if there is any way to view an AP's list of ...
I've enabled option 82 on the WLC, but when I watch clients pull DHCP the 82 option isn't showing up in wireshark. Any Thoughts? Thanks, Skymeat
Resolved! Cisco-ISE
Dear Experts, Kindly helps us to understans how the cisco ISE communicates with the Cisco WLC. ThanksThushara.
