Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have a WLAN SSID that currently does not have flexconnect enabled. I am preparing to deploy some APs at a remote site and will use local switching there to save WAN bandwidth. If I enable flexconnect on the WLAN and not the APs, will clients curr...
HiI have a WLC 5508 and 4408 servicing 100 APs. the problem is client wont connect to the closest AP! this problem leads to creating over association situation for one AP. I have tried disabling the slow data rate. I tried the Client Load Balancing ...
Hi,We are starting to see requirements for the new 802.11ac AP's to be deployed for Voice/Video applications (Lync, Jabber) and I want to know the "rule of thumb" for calculating the number of devices per AP (2700/3700 models).In the past 802.11b/g/n...
Hi, I have two WLC 8500 working in SSO and with nat enable feature configure in management interface. SSO is working, but i have to configure NAT before SSO becasuse when SSO is up, ip address and nat are greyed out in managemente interface. Some AP'...
hello,was hoping someone might be able to assist with the following: i am trying to configure local LAN ports on my 702w AP's for access mode and vlan from AIR-5760 CLI. can find good examples of how to do this in Air-OS, but not in IOS-XE. i mana...
Hi Cisco,I need to change the SSID name in Flexconnect mode. However it seems not possible to parallel run the old and new SSID in single VLAN. What is the recommendation to have the both SSID with same IP range, Auth server, so that we will have tim...
Hi,I would like to schedule the enable or disable of a specific WLAN only in a specific AP-Group.Is possible to do with a Prime?Regards.Mirko Severi.
Able to get voice working on the 702W but now would like to use port 1 as a data port. I have been no been able to connect via data. the AP702 is connected via 2960S access port. If you have been able to get the data port working on the AP702 ca...
Resolved! Add MSE on Switch 3850
Hi,Does any body knows where to add the MSE key has on a Switch 3850, on WLC the command is config auth-list add lbs-ssc <MSE Ethernet MAC> <MSE key hash> thaks for your help.
Hello,in campus I have virtual wlc (7.6.100) and 20 AIR-CAP1552E-E-K9 and 50 AIR-CAP1602E-E-K9. After some complaints from the clients that are just a few meters away from AP and on those AP's I don't have any clients. On vwlc everything seems fine, ...
I'm trying configuring the AIR-SAP1602E-E-K9 for working with only one antenna. In Network -> Network Interface -> Radio0-802.11n 2G.Hz I put:Recive Antenna: Right (A) markedTransmit Antenna: Right(A) markedInternal Antenna Configuration: Disable(li...
Hi all. Have a question. Can I put two antennas in different rooms using a single access point?
we are following this doc:http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00806e367a.shtmlWe are at the part that wants us to:6. Combine the CA.pem certificate with the private key, and then convert the file to a ....
When contracting an SMARTNET for a WLC, do we have to consider the actual number of AP's or the maximun?For example, a WLC-5508-50-K9 can handle up to 50 AP's, but at the moment there is only 24 AP's in the network.Which SMARTNET do I need? CON-SNT-C...
Is it possible I can load-balance my client ? In our current setup when one AP down rest of the client move to other AP, we need to move them manually or connect/disconnect. I can apply max-association on SSID but is there way I can do it automatical...
