Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Can anyone confirm, if we have HREAP support on WLC CT5760, if yes, is their any design guide, if doesn't support, any alternate solution to get HREAP connectivity with AP's located at a different site and WLC at datacenter and having local switching...
Hi all, Recently, I was implementing a project in the hospital.The general enviroment is that one Core SW connected with three Distribution SWs, running ospf between all（The three Distribution SWs are used for 3 different departments so they need ...
Hi, We got many 2602 AP running under Controller mode. Every night Cisco Energywise turn the power off to these AP's and next morning turn it back on. But randomly in a month few AP fails to come back. When I check on console I see error - The system...
Hi, I know Mobility Work Center(MWC) could be used to configure Mobility Domains, SPGs, etc., and deploy them onto controllers.. but i am wondering how does it work in the following scenarios.. a) The devices discovered already have Mobility configur...
Deployed new WLC 2504 and when clients connect for the first time they take for ever to get an IPv4 address. On the controller the connected client has an IPv6 address initially for a while, then it finally flips over to IPv4. Is there a setting I'm ...
Dear Support,I have to configure a Wireless Trunk Link between two buildings. I'm using Outdoors AP 1532 with directional Antennas on 5GHz. I want my Wireless Trunk to word exactly like a Wired Trunk between two switches.In each Building I have a 296...
I have 3 5508 controllers on 7.0 software which supports older aps i.e. 1231 ... For new expansion we have purchased 3602's which only run on 7.2 or higher. I have a 4th controller that is on 7.4 ... can I connect the new 3600's just to that controll...
what is the exact procedure when restarting two CPI appliances configured in HA?should the HA be removed first?should the second appliance be 'ncs stop'ped first, followed by the primary ?
I have two WAP4410N access points set up for B/G/N intermittently I will not be able to connect with iPhones or iPads. It seems I have to reboot all devices all the way back to router to fix. Sometimes that does not even work and I have to repeat sev...
Hi All, As we know, an AP stores its last known WLC's in its NVRAM. Is there anyway to remove controllers from that list? i know there is a CLI command to specify a controller - capwap ap controller ip address x.x.x.x - so i am hoping there is an al...
Hi all. We are considering using 1941Ws at a number of our branch locations. The routers will be installed in metal cabinets. In order to get the antennas out of the cabinet we are considering using an external unit such as a AIR-ANT2544V4M-R. Now th...
hi all,i have cisco WLC 2100s,we can not access the WLC,when we do console to the WLC the logg shown is :Bummer, could not run '/usr/bin/gettyOrMwar': No such file or directoryBummer, could not run '/usr/bin/gettyOrMwar': No such file or directory an...
hi all,my bar code reader motorola MC9190 can't connect to wifi net with wpa/wpa2-tkip psk. i receive the following error: TKIP MIC errors reported in EAPOL key msg from client 40:83:de:89:0a:33 WPA_KEY_MIC_ERR: 1x_eapkey.c:618 TKIP MIC errors report...
I just installed a 2504 WLC (7.6.130) for a customer of mine. This is used just for guest wireless and has it's own dedicated internet connection. When testing bandwidth for the customer we see the full bandwidth when wired into the router 100MB. W...
Hi,I need to buy vWLC license for 200 AP but only part number I can see is L-LIC-CTVM-25A which is 25 AP license.Do I need to buy 8 of these?What if I need to support around 300 AP then Do I need two vWLC controllers ?. can I run them in cluster so t...
