Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have a 3850 switch stack and 1602i Lightweight access points. I setup the APs to join the switch via the DNS entry. When I access the 3850 GUI and go to the wireless controller to change the APs configs such as the names of the APs or their IPs, th...
I see this message come in from Cisco Prime every now and then on a 1242. I see other people have asked the question a few years ago. Has anyone else taken a look and figured out what the problem was? 1. Alarm Condition:Radio administratively up ...
I have just deployed a new 3850 with the integrated wireless controller and 2 2600i APs. Before joining the APs to the controller, I upgraded them to the latest LWAPP image. It appears that they were downgraded when joining the controller the first t...
Resolved! Fool question
Hello eveyone. Sorry if this questions is fool, but I visited an Hotel because they have isssues with its wireless network, they have four Wavions antennas, but they're working on channels 3,9,10. This antennas give service to rooms, beach, lobbies e...
Hi all,i have two WLC configured in my network and almost 300 AP. The APs are configured in DHCP in the same VLAN of WLC with (IP, subnet, GW, domain name and DNS) and i would like to reach the APs through Hostname, is it possible? Is there same way ...
Hi all, We are facing a strange problem at a client's wireless solution. Solution with 4x WLCs 5508, running v7.3.112.0, spread across 2x DCs. All 4x are active (no HA) with two mobility groups. The SSIDs are associated with a group interface (vlan s...
hi all,i have cisco wlc 7.6 and i configured auto contain feature for rouge APs as the configuration guide and then click on apply and save configuration.but when go to monitor tap to see the status of rouge AP I found that they are in alert state (w...
Hi all,I have a query on onboarding iOS, Android and windows devices through Cisco ISE.I understood that we are going to provision and onboard above devices issuing certificates.Do ISE has Certificate authority where it can generate its own Root CA a...
Hi there, We have here an issue with Cisco ISE. When I create a guest account with the sponsor portal We can´t access the Wlan. On tne Cisco ISE Operations \ Authentications returns the error message Event "Authentication" Faulure Reason "24206 ...
How can you see what the acl on our WLC5508 is denying? The counter keeps on going up but what is getting blocked is nowhere to be seen.
Hi,I'm just wondering if it's possible to integrate cisco access point (either lightweight or autonomous) with other wireless vendor, such as ruckus, HP wireless, aruba, etc.Is this integration possible ? any document that can explain it?thanks
Dear friends, I experiencing problem with HA between two 5508, we have 6500 series core in VSS, our WLCs connected as WLCs>>> switchs>>>core sw, when i setup them everything works fine they see each other and HA works, but randomly Active HA looses...
Resolved! AP software
I upgraded my controller and pre-downloaded the image to all of the AP's for a later reboot. When I try to reboot the controller I get the following message.AP software being upgraded, please try again later All AP's show the image has been pre-down...
All, I am in the process of a new WLC install with five 3702I APs. The configuration was gone well up till now..... I am having issues with DHCP pulling IPs from the correct scope. The WLC is in a different VLAN (10) than the APs (142). What am I...
How would you configure the IDSM-2 to place the VLAN’s for the SSID’s of the WiSM-2 thru the IDSM-2 inline?How do you configure the Wism-2 and an IDSM-2 to place the wireless users thru the IPS?What is the best, inline VLAN pairs or VLAN groups?
