Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
hello guysI am currently designing a platform for a guest network, which must be isolated from the local network, the following equipment:ISE 1.2 (Cisco SNS- 3415-K9) WLC 7.0.230.0 (Cisco controller 5508)---> wlc ForeignWLC 7.0.230.0 (Cisco controlle...
Hi All, I have Configured DHCP snooping and IP source guard and Dynamic arp inspection on my 3560 and 3750 Network Switches,on both of them I'm facing that issue. (the printers and access points are configured to get ip addresses via DHCP), but when ...
Hello,What we are trying to do:John logs on to wifi using RSA fob for password. RSA sends back auth request with attibutes to WLC 7.4 that magically knows how to interpret the attributes and puts John on vlan 10. Mary logs on with her fob and gets pu...
j'ai besoins d'aide pour la configuration en autonome de l'AP 1600.
Hi all,I upgraded MSE today from 7.2.110.0 to 7.5.102.101 using the release notes, after the upgrade I get the following error:[root@ukgrelg-174-mse init.d]# /etc/init.d/msed startStarting MSE PlatformStarting Apache HTTPD ServerStarting Health Monit...
Checking to see if there is a way to control how the inside controller load balances to 2 anchor controllers. I was told its connection by connection, but wasn't sure if its true, and if that could be changes to a particular hash or something.Thanks...
HiWe've just purchased the a VM Version of MSE (L-MSE-C3-W25) installed on vSphere.Have followed the guide, gone to add this to WSE and it wont connect.Looking at the console it says to type /init.d/msed.start, I get -bash: /init.d/msed: No such file...
Hi,In my environment there's a 5508 (firmware 7.4.110.0) and ap 1600 with a ias radius server. All wlan are in flex-connect local switching, one client try to connect on a wlan but not receive ip address. After enabled debug aaa all i took the log c...
Resolved! IOS Root and WGB Connectvity
Hi Experts,What are the implications of blocking band 3 between a WGB and Root using the "dfs band 3 block" command. Note, this is enabled by default on IOS AP's as stated below. Does it in anyway affect the use of 802.11n MCS rates?http://www.cisco....
Resolved! Block Andriod Devices
Hello Freinds ,is there any way that i can block andriod devices to connect to a specific SSID on wlan controllers.
I have a training room with 4 PC's and right outside of this training room is a 3500i series LAP. Only two of the PC's are associating to it, and the other two are associating to an AP 2 floors up which much slower data rates.I am wondering if I can...
I just created an AP group for the first time on my 4402 controller. When I went to add an SSID to the group, it says it will disable the WLAN. Does that mean all users on that SSID will be disconnected? How long would the loss ...
Resolved! Grouping AP's together in PI 2.0
Hey Everyone,I have recently deployed PI 2.0, and I am wondering if what I would like to do can be done.I have approximately 1,000 AP's deployed in various retail locations and was hoping I could group them all together into one group so that I can s...
Resolved! PI and wlc compatibility
Hello experts,I have 2504 wlc with 7.3 code and Now we installed new Prime infra 2.0.My question is :we decided to upgarde wlc software to 7.6.is PI supported wlc with 7.6 ? if not then what I can do ?Thanks
Hi,I´m planning right now a local Guest Access breakout for a Branch Site which is connected over a HREAP AP to a centraliced WLC . If I have it correctly understand then I´ve to do following:1. Creat a Guest SSID on the centralized WLC ( 5508 ) / ...
