Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi everyone,Seems as per cisco all WLC --5500/2100 etc are effected by sslv3.Need to know if there is any config change that can be done without doing version upgrade? RegradsMahesh
Hi Guys, I have 4 Cisco ASA running version 9.1(3), Computer Associates Spectrum able discover but not able to discover by CA Computer Associates eHealth.Both Spectrum and eHealth discover ASA devices via snmp.Is there any related bug or special conf...
Hi, I've downloaded ap licence for cisCo wlc 2504 with wrong UDI product Id. Now I am unable to install licence because of incorrect UDI.How would I download again with the correct UDI since, licence order has been already fulfilled.Your suggestions ...
Hi All,I have an interesting problem. I have a Cisco 2504 WLC, and six Access Points that are associated to it. I can reach 4 of the access points, which are connected to Cisco 300 POE switches, but the other 2 I cannot ping, telnet, SSH or find in ...
Hi All,I am trying to do image upgrade through cisco site & when i try loging in it shows wrong credentials thogh i use the correct one. Where exactly i should enter login cred for cisco.com in prime.
Hello community,Sadly the vWlc does not stop to hurt me!Firmware: 8.0.110.0APs in FlexConnect mode.I have configured one wlan. No wlan password. I gave this wlan the interface with the name "officeVlan10".The settings for the interface are as follow:...
Hi,I have a requirement where I have 2 Physically separated networks. I want to use 1 controller and connect both the networks to this 1 controller with 2 diff SSID's.Is that even possible? As far as I know we can connect 2 diff networks as long as t...
I studied your article (CoAP) in http://tools.ietf.org/html/rfc7228. we are developing Home automation Solution with IoT enabled devices. I have following doubts to provide the seamlessly solution for Home Automation. 1. I have some appliance with Wi...
Hi All, I am in the process of installing a virtual WLC for one of our small office (which will have 2 AP 3502). This is our first deployment of vWLC in our environment.I am using 7.6.130.0 (AIR-CTVM-K9-7-6-130-0.ova) on ESXi version is 5.5. We follo...
I have enabled HA SSO but have lost connectivity via the web GUI. I can ping all interfaces and HA is successful. Any ideas would be appreciated.
hi, I have a pair of 1600 AP's in stand-alone mode, configured as a wireless bridge. there are a few vlans going across this link currently.I started to research wan compression options as a means for optimize the throughput, but then wondered if I h...
I want to move maps from WCS to NCS, can you tell me any method to export or import maps from wcs to ncs or any other short method.
Anyone know how to force android phone to prompt user for certificate download? We don't experience any problems with iphones. Just select SSID , enter active directory user ID, enter password and it will prompt for certificate download. Once downloa...
Hello all, I have ISE v1.2.0.899 and installed up to patch 12. I was about to install patch 13, but now patch 14 is out. To me patch 14 is too new and I've heard that later patch versions may cause new issues. I'm thinking to apply patch 13 as planne...
Hello,The Wirless LAN Network bulit is as follows -1. 1 x 4404 WLC2. 40 x LWAPP 1131AG Access Points3. Windows Clients used by the Laptop Clients.4. Only one Wireless VLAN across the Capmus network - hence AP's, WLC & Clients are all in one VLAN / IP...
