Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Does phase reversal in the 5GHz band play a significant role at sites where the presence of WiFi inverted interferers is detected by Cleanair? I have a site experiencing some WiFi inverted interference and we can't seem to track down the source. Just...
I have tried to search some documents, where I find Cisco saying 128 users can be supported. But I am confused is it? if, yes is it like all together 2.4/5.7 ghz or single radio !!!!
Hi guys, I've configured a brand new 2504 wlc to replace an older model and it's working fine, but some of the hosts are facing problems while trying to connect. They do all the authentication process, but at the end they don't get an IP. I've checke...
How do you config AP's to roam to the strongest signal without using WDS?I have 3 AP's in a warehouse, 2 - WAP321, 1 - WAP371. No domain services available, they are just standalone AP's with local SSID and key for authentication.They have same SSID ...
Hi all, I have a 3750G Wireless LAN Controller that after trying to upgrade the bootloader now refuses to boot at all. I get no console access what so ever on the screen and when consoled onto the switch I can't access the controller console through ...
All: I'm working on a solution for someone who already has a Cisco WLC 2504 running 7.6.100 and 2602i APs. They are running iPhones with a SIP application instead of purchasing Cisco 7925G phones. They are having issues when roaming to different AP...
here is an a demonstration of how to configure vlans and ssid on a auto-ap , what i dont understand is when i configure the ssid under (interface dot11radio0) and the vlan under that command , why do i need to configure sub-interfaces for the "fastet...
I want to deploy APs in remote locations using FlexConnect. I will give the APs static IPs on the local LANS, but I want the clients to get DHCP from the existing WLAN back at the central site. Not sure what needs to be set on the WLAN for FlexConnec...
Dears, Need your support to know how i can get AP led status from WLC.As we know there are more than led status "cycling red-amber -green & Blinking green & blinking red &green &...." how we can see this from WLC. Regards,
Hello, I have two Cisco Aironet 2602i Access Points currently connected to a wireless controller. I would like to remove these from the controller and reconfigure the access points for stand alone operations. I have not done this before and would app...
Hello,I have a very strange scenario with 2504 WLC. It is deployed as an Anchor with 5508 as the foreign. In summary, my set up is as follows:2504 - Anchor (version 7.6.120), Port 1- MGT, Port 2 - Guest subnet, No AAA Server, Internal DHCP server5508...
We currently have a wireless infrastructure consisting of 2702i access points and a 5508 controller. We have a guest (Internet only) SSID and also a private (corporate) SSID. We are currently using PSK for the corporate wireless but I would much rath...
ASA version: 8.2(1), ASDM version: 6.2(1), Device Type ASA 5540I use the Wizard to create a clientless VPN. When I try to access VPN, it will not display a logon banner. I get page can not be displayed.webvpn enable OUTSIDE svc image disk0:/anyconnec...
Hi All, I recently started a new job where there is no documentation whatsoever anywhere. I have about 200 access points spread across the planet, and the majority of them have WEP keys. I have access to the APs and can see the encrypted versions of...
I´m looking for the CLI command to asign the primary controller name and IP from the master controller. So as AP's join the master controller, I can move them to their new Controller. I would like to do this thru the CLI of the master controller when...
