Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Dear Friends,i have dozens of APS unable to get an IP address from DHCP (core 6500 series switch). i am getting the following message on APS%CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ipi have another DHCP server on windows...
I have created a template to be applied to a group of access points. When I run the template, the template does not get applied to the ap's. I attached a screenshot of the results. Can someone take a look and see what I am missing? TIA
Hi All,How much size logs can we store in WLC ? IS there any way to see the old logs ?Plz provide links if its there?Thanks,Regards,Vijay
im looking to convert this AP to Autonomous mode but i dont see the autonomous mode IOS software on 2700 but i do for 2600 ? do they operate in autonomous mode ?
hi all,sorry for a noob question, i'm still learning wireless.i've searched cisco and CSC on how to disable broadcasting of SSID.i have multiple SSID on my AP.is it normal to still see the SSID on the sh dot11 bssid command even though i disabled its...
We are deploying a medical cart that contains a video camera, computer and 2600i ap. The ap will be used as a WGB. Our wireless environment is controller-based. I suspect this cart will be moving around to several locations. It is unclear to me h...
I need to get the serial number of SFP in WLC 5508 ver 7.0 but can't find the command, is this possible and if yes how can I get the S/N of SFF in WLC?
I need to block several domain in my network. But i can't see any domain blocking menu in WLC version 7, If i set a rule in ACL it would be pointless if the domain have a several IP Address. So what should I do ?
Dear Experts I am facing an issue at one of our customer, where in we have deployed AC-Modules on CIsco-3602i Access Points backed by WLC-AIR-CT2504 with below system information"Burned-in MAC Address............................ 68:86:A7:36:9B:80Maxi...
Hi! I have just installed a Virtual WLC at home for lab purpose. Now i want to connect one accesspoint to my wlc, but for now the WLC says "0 access points supported". Can i somehow still use the evaluation licens and connect a accesspoint to the wl...
hi all;I have one RAP one MAP,I set the Bridge data rate to AUTO on both, how can I show the current data rate between them?what is the MAX range I can space between the RAP and MAP in outdoor and open area ?Thanks for the supports
Hi,the following config works on AIR-AP1142N-E-K9, AIR-AP1242AG-E-K9 and AIR-AP1242AG-E-K9, but it works not on several tested AIR-SAP1602I-E-K9.The config is the same, except for "FastEthernet" replaced by "GigabitEthernet" depending on hardware, an...
I'm a Cisco employee so you can say I'm professional, but this really puzzles me: I have this Cat 6506 switch with SUP720 and latest image. It takes WISM card but not WLSM, the error msg being "unsupported". I'm using 15.1(2)SY3 image and used 12.2.3...
Hi all,I understand that it is possible to have the WLC send different NAS-ID attributes to the CIsco ISE so that I can create specific AuthZ policies based on that NAS-ID attribute.The only thing is that I cannot see anywhere in the FlexConnect AP G...
Hello All, I have an envorinment with 18 APs wich are mostly 1242AG and one 1142 AG. I have a 2125 Wireless Lan controller servicing the network at this time. I have set up the 2504 wireless controller on a test network along with a spare 1242AG AP....
