Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi,I've installed CMX Analytics 7.6 according to the user guide (http://www.cisco.com/c/en/us/td/docs/wireless/mse/7-6/CMX_Dashboard/Guide/Cisco_CMX_Dashboard_Config_Guide.html) and setup zones in Prime v1.4, so far so good.My problem is that I have ...
Currently looking for a solution that will detect and or disable Computers that are simultaneously connected to both the wired and wireless networks withing a single building. The wireless and wired network utilize physically seperate cisco equiptmen...
Hi All,Hope you can help with this -I have the following:A 5508 in a remote datacentre and several sites with AP's running in flexconnect mode, connected to cisco switches.I have an ssid on which I want to run some push to talk "phones" which I belie...
Hi All !Currently i am working on one assignment and willing to integrate the Identity service engine in the network. the only problem is that wireless network deployed earlier is from other vendor i just need to know that either ISE had the functi...
All, We have a new 5508 controller that we are trying to get setup to use our Motorola 9060G handheld scanners. This device uses WPA-TKIP and has been working with a Symbol controller without issue. I need to retire this controller so started re-crea...
I am migrating APs from a WiSM running 7.0 to a 5508 that is running 7.4 but I can't find a way to get the 7.4 code pre-downloaded on the APs while they are connected to the WiSM. We're a 24 hour environment so I'm guessing I'll have to migrate one a...
hi allfor the CMX it is required a layer 3 router to apply the policy based routing that redirect the HTTP traffic to the MSE to engage the banner in this traffic,I need to know, the MSE receive layer 3 ip packet from the policy based routing and the...
Hi All, I'm working on a project for a Laboratory, where we will be installing Access Points. There are some Labs in the building, where the environment is controlled strictly. Any recommendation on guide lines that should be followed while mounting ...
Hello All; I was wondering if I can use a 5508 controller currently used as an Anchor Controller for Guest Access for 5760 controller and 5508 and WISM configured as Cisco Unified Wireless controller, or do I need to convert the guest controller 5508...
How do I disable DNS queries going to the AP from the wireless clients? The AP are coming up from vulnerability scans to allow DNS Server Cache Snooping Remote Information Disclosure. Looks like all the AP is working to serve DNS requests.
Hello!Trying to install a virtual instance of MSE 7.3.101 on an VMWare ESXi host. Have configured with 8 Cores, 11 GB RAM but have encountered errors when setup is completed and the services restart.It appears that the MSE services are not starting c...
I have a small collection of 1131 AP's that have broken case lids, as I am sure others might also since they are a marvel of plastic engineering. Anyway, I hate to throw away perfectly good AP's but I can't re-deploy them this way so I was wondering...
Hi Board,I have a 7.4 WLC pair - one as primary and one as secondary WLC. They are not doing AP-SSO.I'm aware of all the design and configuration guides, but there are still some questions.Primary WLC: 50 AP count / Secondary WLC: 500 AP count (due t...
Hello Cisco Friends, I have general question about the 871W and 871 Integrated Services Router. Can I upgrade my 871W with the same IOS image running on the 871 router? I've tried to the use the cisco software navigator but 871W is not a supported p...
hi All, My query is to understand how much time will an AP take to failover to its secondary WLC(Backup) incase primary goes offline.Whats the heartbeat time for each AP to verify reachability to WLC. also what is the purpose of AP Fail over priority...
