Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I'm regularly getting a warning stating that "The system is running low on diskspace, please refer to online help to perform disk cleanup.". I looked at the appliance information and it stated that the fullest partition was the optvol and 52% was use...
HiI have ISE 3315k9 1.2, WLC, catalyst 2960 and PI 1.2I use prime to monitor all user connected on the network (wired and wireless)For wireless user, there is no problem, I can see posture, vlan, ACL, IP adress, user name ...But I am unable to view i...
Hi everybody,Iam reading through the frame handshake in WiFi. Also went through some of the good articles in this forum.I understand that to avoid collision, RST/CTS handshake is used in the wireless Air medium.I have attached the RTS-CTS handshake a...
We have a new Cisco WLC 2500 device and I'm trying to perform an initial setup, it first asked for a management IP and when it reached to the question of asking for a multicast IP, just wondering what is this multicast IP? and what does it do?ThanksJ...
Dears,One of our customer is having a Cisco AIR-WLC2112-K9 , we purchased an AP AIR-CAP16021-C-K9 , based on the supplier recommendation ,As I understand , CAP16021x Series require a Wireless Controller with firmware 7.4.x and above where as Cisco 21...
Hey,If I want to deploy a number of 3702e AP which support 802.11ac am I ok to use the 2504 wireless controller?Thanks,Jonathan
I know that the 3700 itself will drop to 3x4 MIMO if it only gets 15.4W of power (takes 16.8 with 4x4). If I add in a WSSI module, I know that is not enough power to run the WSSI module. We'd like to deploy our APs with the module installed and li...
After I upgraded WLC 5508 from 7.2.111.3 to 7.4.121.0, all 3602i APs don't associate with the controller. All APs were working/associating with controller on 7.2.111.3 at same setting. IP address of APs are setup as DHCP.The error message is "AP c...
I am trying to find Cisco's current recommendation for the maximum number of LAPs per VLAN.I've read (and remembered from a previous training course) the recommended maximum is 60-80 LAPs per VLAN and fewer than this if the APs are on the same VLAN a...
On this command which IP address do I use? ap-manager? or management?
Hi Everyone, I am unable to access the WAP.When i try ssh it do not take current crendentials.IS there any way that i can login to WAP via WLC?Model of WLC is WLC2112-KP RegardsMAhesh
All, I would appreciate if anyone could provide clarification on my current understanding of Converged Access mobility design for WebAuth and guest access. My setup is as follows: (WAP)---(MA)---(MC)---(Firewall)---(GA) Wireless Access Point (WAP) - ...
Dears,We have 800 bus station and we need to occupy all of them with wireless signal,We can use outdoor 1500 outdoor series AP, but we think it is not right to use such type of AP for a little bus station area, we can use indoors but the we need to f...
Hi Everyone,Please could someone help point me in the right direction, I'm trying to setup a wISP with current cisco infrastructure with the use of FreeRadius,my intention is to rate limit specifc users after certain amount of time, I've managed to g...
Hello Guys I have an NCS (cisco prime) 1.3 in appliance model (IBM server) and we are wondering if we could upgrade it to 2.0 (with out virtualization)The 1.3 covers the 2.0 requirements.The reason for the upgrade is that we are hitting the cscud2602...
