Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
i don`t know routing protocol for wireless Ad-hoc Network .. i need a help in this topic ,,, Thnx "
Hi,I have an issue that has only just started in the last couple of days. I have clients using a Guest Network which has been anchored to another WLC. The clients associate and authenticate to Access Point/Controller correctly, although the cannot ge...
Hi guys,I have a problem when adding a map to WCS. I have a floor image file sized 1366x768. When I add this picture to the WCS, the WCS automatically convert this picture to 92.6 meter x 52 meter1366x768 --> 92.6 meter x 52 meter. My goal is to conv...
Hi All, I have requirment to enable the AES encryption on the management VLAN traffic between connected root and non root bridges . can any one share the configuration guidelines please ?? below is the network setup . Router<---->SW1 ( mai...
The GUI times out after 60 seconds.Since the the "exec-timeout" setting has a default of 10 minutes (if I'm not mistaken), I don't think I could change the timeout value with that command.Under the "Association" tab of the GUI, there is an "Activity ...
Hi, i am upgrading my WLCs from 7.0 to 7.2 (and 7.3) version and wondering what is difference between AP mode H-REAP (in 7.0) and FlexConnect mode (in 7.2)?Appreciate your input.
We have started having some issues with our Cisco Aironet 1200 wireless router dropping all connections for a few minutes and then picking them back up again. At times, I have to actually physically pull the network cable from the router and plug it...
Hi everyone,we have a AP cisco AIR-AP1131G-E-K9 Version 12.4(10b)JA, and we would like to do automatic backup of CLI configuration to one server, and we dont know how to do.For example: On router and switch we use this kind of configuration to do aut...
Hello all,My customer has upgrade his 4506 from 6L-E to 7L-E 10GEEver since then if he run the command show dot1x interface gigabitEthernet x/x detailssome information are not been displayed (below are missing information)PortControl =...
Is it possible to set an Aironet 1232AG-A-K9 as a repeater while still using a 4402 controller? I have some wireless security cameras in our parking lots that I need to extend wireless to and I have a handful of 1232 points that I am not using. I h...
hello,I have a 2112 wlc and 6 1142ap's. I noticed that the 2.4ghz channel is filled with lots of networks but the 5.0ghz area is empty. I tried to manually change the channel but it keeps reverting back to 2.4. Any suggesstions?
HIIm having the same problem with two new cisco AIR-LAP1131AG-E-K9, when I connect them to my switch they come with a Green, Red, Orange blinking Status LED. The ethernet is Green and the radio is BLinking OrangeThe problem is that this combination o...
Dear All, I am currenctly confused in choosing what type of Cisco Prime. 1.Which one should I choose? should I order Cisco Prime NCS or directly purchase Cisco Prime Infrastructure (since Cisco Prime Infrastructure has the feature of NCS)?2, Why does...
Hey All:Ran into a strange issue today, two 2504 controller's, one upgraded (from 7.2 to 7.0 due to 1310 not working) to the new firmware fine, the other chucks back a signauture issue, i've seen alot of post's about the 5508 having this issue, but n...
Hello Everyone,Is there a doc available for setting up multple WLANs, with having each wlan on its own vlan?THanksEquipment:2106 WLAN ControllAironet 3502 AP
