Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Currently we run a 9800WLC in our data centre which controls AP's across 45 sites give or take.(This is configured through Catalyst Center btw)Guest network is central switched, central auth with ISE doing the guest portal.Another SSID is central aut...
Running into an issue where about half of our 41 brand new Cisco CW9166I-B access points are not registering on our WLC. When consoled into the APs, we noticed after the initial boot phase, the wired0 ethernet port constantly goes link up/link down. ...
We have wireless setup with Splash page cut through problem is some of client PCs disconnect sometimes when we are uploading files, on client PC wireless looks connected but after a while splash page authentication appears again to authenticate, can ...
i have an Ekahau Site Survey 9120AXI APs with transmit power 9 dBm (EIRP 14 dBi) on 5 GHz band, what is the equivalent setting on 9800 WLC in RRM / TPC max level? do i set on the WLC RRM/TPC 14 dBm and antenna gain 10 x 0.5, or do i set on the WLC RR...
We have a couple of units of Wireless LAN Controllers (models AIR-5508-K9) configured in high availability.Such models is on a End-of-Support status along with many of the lightweight access points which are being controlled by them. I would like to ...
Unable to connect to Meraki APLogs on meraki indicate- Client failed 802.1X authentication to the RADIUS server.auth_mode='wpa2-802.1x' vlan_id='160' radius_proto='ipv4' radius_ip='172.24.32.10' reason='radius_login_failure' radio='1' vap='0' channel...
the below WLC not registering the AP , the same time indor APis detecting .Please assit for the issue , below are the neccery detaisl for WLC & AP WLC 5520 -------------------- (Cisco Controller) >show sysinfo Manufacturer's Name........................
Is anyone else trying to use a Desk or Desk Pro as a mobile unit? We use them for telemedicine, but are having issues with the devices staying connected to wifi. Anytime they move, it can take up to 5 minutes to reestablish a connection on the new AP...
Hello,I've just received new C9166i APs, they have 3 radios installed (2.4G/5G/6G).Can I set the Tx power per radio or only per AP -so for all 3 radios ?Regardless the answer -is this a general rule for all CISCO APs or some models are different and...
1. I disconnect the PoE power supply2. I hold down the MODE button3. I connect the PoE power supply4. I hold the MODE button for more than 30 seconds5. I wait for the AP to start upAfter this process, the AP tries to connect to the old WLC, which mea...
Hello, I am trying to boot one of my aironet 3802i's via manually installing the ME firmware, however when I attempt to type boot on the uboot console it says bootm is an unknown command. Is there anyone who has in depth knowledge on how to flash the...
I would like to know we can assign 2 or 3 VLANs on same SSID or not? If can what should I notice in configure AP?
Hi there, i have the same problem. Installation 9800CL 17.9.4a and 17.6.4 , APs 9120. there is no software version or APSP available to download from Cisco. what should i do? Thanks
Hi All,I need clarification on traffic passing through Mobility tunnel between Foreign and Anchor controller.DHCP\Authentication\Switching is all Central. Once any traffic like radius\DHCP\DNS\Data traffic will reach Foreign WLC it will go to Anchor...
if wlc A and wlc B both have tag persistence enabled.on wlc B, tag source priority is "filter" then "AP".if AP A is move from wlc A to wlc B, will AP A reconfigure all it's tags from wlc B "filter" or it will retain it's tag saved in the AP itself???...
