Buy or Renew
Buy or Renew

Wireless

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Error in importing certificate

G'day Guys,I am trying to install the certificate on Cisco Wirless Control System and using the steps defined in the given below URL:http://www.cisco.com/en/US/docs/wireless/wcs/7.0MR1/configuration/guide/hard.html#wp1042471I am getting error in step...

Using a single user name for RADIUS

I have a WLAN with 5 1200 Series AP (A/G) configured for Fast Roaming using the Cisco supplied documentation. Can I use one user name for all of my devices to connect to the Internal Radius Server? This would be similar to having a passphrase for WPA...

Resolved! Is it possible to block MAC on AP?

Is there is a way to block a specific MAC address from associating with an Acces Point yet still allow them to connect to the SSID that a different AP is also broadcasting? I have read some posts that talk about doing this with ACLs on the AP but I w...

Resolved! WLC Management

Hi All I just had a question asked by my manager about  controller management. We have a lot of WLC across the county and we are looking to find out if Cisco makes an appliance that we can setup that will let us manage all of our WLC from one device....

EAP-TLS with server 2003 RADIUS and WLC5508

I need to configure a windows server 2003 for RADIUS authentication along with a WLC5508 WLAN controller for EAP-TLS authentication. Has anyone done this before and if so, provide some assistance towards this? I am not very familiar with Windows serv...

rajarora4 by • Level 1
  • 482 Views
  • 0 replies
  • 0 Helpful votes

Client authentication issue with WiSM2

we have a special SSID that uses a full email type address for authentication (eg bob@company.com).  This works fine on our WiSM (model WS-SVC-WISM-1-K9), and clients authenticate as expected.  However, on any AP that is joined to our WiSM2 (model WS...

Resolved! Cisco 1262 Maximum transmit power

Hi,I will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas.  What is the maximum transmit power, 20dBm or 23dBm?I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.Than...

mcaoile by • Level 1
  • 1190 Views
  • 4 replies
  • 0 Helpful votes

Resolved! mesh parent

I have few questions for mesh network:what exactly is a parent, child and neigbor in mesh network1.can a mesh access point act as parent or child to another mesh neighbor ?2. an electronic temperature gauge connects to root access point eventhough an...

suthomas1 by • Level 6
  • 1757 Views
  • 1 replies
  • 0 Helpful votes

CISCO WAP4410N AP

Hi,i am using two  Cisco AP 4410N series in my network .Wants  to use MAC address Filtering but it supports  only 20Nos  of MAC to add in the AP.Is there any way like IOS upgrade the AP supports more MAC Address to add.Please Advice.Thanks,Saroj

Resolved! MAC hash or round robin

I am in the process of revamping our wireless solution. I am interested in VLAN pooling and am wondering if it is done round robin or with a hash. it is important for us to keep the same IP addresses so the MAC hash would be ideal over round robin in...

IOS 12.2(33)SXJ sw compability in upgrade.

Hi.I had a discussion about this subject where I asked about ANY complications during this necessary upgrade.In the release notes NOTHING is mentioned about loosing ALL portchannel configurations for the already present WiSM cards...I asked this:----...

Load more
Review Cisco Networking for a $25 gift card